MAT15MNBGW0 Maytag Washer - Instructions

replaced handle

As per partsselect.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

removed the controll panel,removed back. ,and then top ,and sides. pryed top off adjtater take out bolt in center ,remove top ring of outer tud,remove adjatater and large nut and coller,take off drain hose lift out outer tub and seal,. put new seal in new tub install in reverse order . hardest part was geting sides lined up

After seeing video it was easy . Took everything apart tub,basket,replaced all springs. Tub wear pads. It took longer because I cleaned eveything,took my time. There was a lot of deposits on tub and outer tub also some rust . Put it all back together all nice and clean . pluged it in put it in spin cycle and the motor just hummed. I than check to see if somethig was stuck no .Pulled motor tested it with out a load and did not work. Motor start winding went. Motor died. 2n one in 7 years. So I fixed that proplem I am a new owner of a Speed Queen washer and dryer .

It was actually much easier than I expected. The worst part was dealing with the gear oil as I drained it to clean out the plastic pieces that came off the gear. To see how to fix things like this, I went to Google, enter my model and what the problem was and watched a repairman do it. It seemed easy and it was.

FIRST, I went to the wrong web site, and thought based upon their diagnostics that I had a sock stuck in the pump. The machine would run, but not pump nor spin. Further, I had no idea precisely how to get at the pump, which is located at the front to the machine. Bailed 20+ gallons of water, and a full load of wet clothes out, took the machine apart from the back (precisely opposite to the correct approach) and took the pump out--no socks, pump OK. Searched with the machine Model # and found Parts Select, and its help video, statistical analysis, and feedback. I jumped the broken switch, so I could wash clothes (a cheap piece of whirlpool engineering dedicated to the appliance repair trade's pension plans, no doubt), put the machine back together, and ordered the part off the web site page with the repair video. Wrong part showed up two shipping days later, and after talking to customer service, they shipped the correct part, received two days later. Took me less than 20 minutes to install the right part. It took me at least 45 minutes to repack the wrong part, drive to the post office, and then I had to pay postage, and am still waiting to get my $37 back--oh, and I am out the money for the right part while waiting to get my money back for the wrong part, and paying postage to send it back--and for $4 gas to get back and forth to the post office, and spending my time correcting the part of the problem not of my making. Prolly net/net I will still be monetarily better off than having called an appliance repair guy and getting a stiff bill for the house call, and full retail for the part.This web site nailed the problem based upon my symptoms--and I ordered the part shown in the video that was identical to what was broken in my machine, but was initially sent something else. If I had found this web site first, I would have saved myself three hours of figuring out how to take the machine apart backwards without ruining anything in the process, and removing a pump that was fine. Putting it back together after viewing the video took 15 minutes.....the only down side of my experience was getting sent the wrong part (a lid switch that did not fit my machine, and did not match what the tech was removing in the video--one with the three long lead wires, ground wire) and paying postage and taking my time to repack and mail.

Very old washing machine began to make a horrible noise and agitator would attempt to agitate during spin cycle. Eventually determined that the problem was in the transmission. The way the transmission works is that when the motor runs in one direction a metal fork pushes on a cam mechanism and lifts a spring loaded gear on the agitator shaft from the gears that make it move, putting it in neutral so that it can spin freely with the basket in the spin cycle. When the motor runs the other way the same fork pulls on the cam and drops the gear down so that it engages with the agitator mechanism. The problem was that the plastic cam pieces on the base of the shaft had worn down to the point where they where not fully lifting the gear clear and it was partially engaging with the drive mechanism. Repair was relatively straight forward except the YouTube video that I was using showed the parts on upside down. All the other transmission parts are labeled with TOP on one side but oddly the cam pieces are not marked. For reference the U shaped protrusion on the cam parts goes on the top of the assembly, not the bottom. All in all it took me about 12 hours to do this fix, but at least 10 of that was simply trying to figure out how the mechanism worked and tracking down the problem. Be sure to refill the transmission case and use some RTV sealant to seal the cover back on when you are done, just like you would for an oil pan on an engine.

There are youtube vids on how to get the thing open. I just wish I'd known the following: 1.remove agitator BEFORE opening the unit up and leaning it back (much easier to work inside the tube with it upright). 2. be aware that a free-floating part known as the skate plate can dislodge while the unit is on it's side/back. It is a generally triangular piece of flat-ish metal between the base of the tub and the top of the drive-train chassis. If it doesn't line up properly after you replace the parts you're going to get a noisy, clanking spin cycle the next time you run the thing (as I discovered).

Replaced broken and worn wear pads per online instruction.also replace tub springs and counterweight spring.all very simple.

We search on line the possible cause for our problem and Partselect offered the possible cause and solution. We watched the video on replacing the water pump.We then ordered the pump and 2 hoses.We followed the instructions and after removing the front panel, we found out one of the pump retainer was rusted away. We tried to look for local supplier and was shock that Sears was charging 20 bucks for a single retainer, which Partselect only charge dollar and eight cents. We ordered the 2 retainers on Thursday and it arrived on Saturday afternoon. We were able to fix the problem and are very happy there was no more leak. I wish the retainers come with the pump even if you include the extra cost to the pump pricing. We could have save the extra shipping charge for ordering the retainers only. I would definitely order more parts from Partselect and recommend it to my friends. Thanks again for your help.

Parts Select is outstanding..They diagnosed the problem quickly..The part was sent within 2 days and we were washing laundry the 3rd afternoon...THANKS!!!!!!

Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!