MAH22PDAXW1 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Margret from Hickory, NC
- Parts Used:
- WP99002106
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The upper dish rack was falling off its track.
I watched the installation video and ordered the part. When it came I reviewed the video and did the repair. Really the only time I used the screwdriver was to get the old wheel off the back part of the unbroken section of the mounting strip so I could use it on the new mounting strip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angel E from Beaverton, OR
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Noisy water pump. Spinner was broken.
I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Burlingame, CA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Pump noise Rattle and not draining water out/ error code
Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- amber from rochester, WA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the pump went out on the washer
took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Atlanta, GA
- Parts Used:
- WPW10388418
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench (Adjustable)
Loose and old belt
First unplug the washer and take the back cover off. Loosen the screw on the motor and the big nut on the belt wheel. Take the old belt off and put the new belt on around the motor but slip the motor back in place with the screw slightly in place but do not tighten it yet. Place the belt around the motor and the wheel but this is hard because you need some one with some strength so the is where my dear boyfriend came in handy. He used his strength to stretch the belt and put it back on the machine so I could put the big nut back on. But if you break a wire you have to know a little electrical to put back the wires back in place with small connectors. I do know electrical also. My machine is working better like new. Carol Rozier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Waco, TX
- Parts Used:
- WPW10143586, WP8540429, WP8540399
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
F30 error code. Water pouring out.
A previous person had broken the actuator switch connection so I replace it and got rid of the error code. But water poured out and I eventually took off the whole dispenser assembly and found a sock had stopped the big hose up where it enters the outer wash drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from West Seneca, NY
- Parts Used:
- W11366227
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Leaking flex pipe
Perfect part...saved me hundreds on labor. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Waco, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn' drain f21 then after I drained it it gave f33
Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from Havre, MT
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
F 21 error
We purchased a new pump and installed it very easily. My washer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from Nevada, OH
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The washer was sending an error code (F21) and it was getting worse about draining I tore it apart twice and decided to order a new pump through your website and it can quick and I installed it and it works perfectly now after a year of cleaning the filter and not getting anywhere
My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Federal Way, WA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
machine flashed code for water not draining fast enough
I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Kalamazoo, MI
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The washer was flashing f-21 code. And the cloths were soaked.
First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Ferrum, VA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Error 21. Drain problem
Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from turners falls, MA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
buzzing noise water not draining
unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included
Was this instruction helpful to you?
Thank you for voting!