MAH22PRBWW0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DAVID from HARRAH, OK
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
would not drain or spin
Replace water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from elizabethton, TN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer washed cloths then would not rinse
Just went by instructions provided by parts web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Bristol, CT
- Parts Used:
- WP8540402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
detergent drawer dropped onto cement floor and front of door broke off
The new drawer came and I took out the the detergent despensor piece from the old drawer and placed it in the new drawer and put the new drawer back into the washer. Now the front of the washer is complete. Good as new. Part also arrived in a timely manor too. Very pleased
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Naples, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My washer was not draining
It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Ruther Glen, VA
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Drain pump was not working properly
First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from West Seneca, NY
- Parts Used:
- W11366227
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Leaking flex pipe
Perfect part...saved me hundreds on labor. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Lyndeborough, NH
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Whirlpool Front loader washining machine F21 error code
Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Trussville, AL
- Parts Used:
- WP99002069
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Grinding noise and dishes not getting clean
Upon removing parts in an easy systematic order I discovered glass in the bottom of the machine. Was able to remove all but the Wash Impeller. This seemed to be stuck and I could not unscrew even when holding the impeller with pliers. Finally broke it. Ordered a new impeller and installed a few days later and everything works like new. Total cost less than $20. Wife is happy - I'm happy. Washing dishes by hand for a few days reminds you of how much we take modern appliances for granted. Oh - by the way. Very happy with the PartSelect service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Springfield, MO
- Parts Used:
- WP99002069
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
motor running - no spray
removed racks - removed lower wash arm - removed filter screen - removed upper pump cover - removed broken wash impeller - replaced wash impeller - re-installed upper pump cover - re-installed filter screen - re-installed lower wash arm - re-installed racks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- melynda from Ruston, LA
- Parts Used:
- W10202464, WPW10111158
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
made a loud knockin banging noise on spin cycle
the repair cost was about 1300$ from a repairman! and they wanted to replace the complete inside drum assembly, so i decided to break it down myself and i'm an average do it yourselfer 1. unplug machine 2. remove water hoses 3. remove the top 4. remove back panel and front complete 5. remove all inside connecting wires but leave them close as to make it easy to reconnect 6. take all three shocks loose from bottom of drum and remove all counter weights (concrete) 2 on front and 1 in back as to keed drum ballanced for removal and 7. remove the complete drum 8. set drum down door side down and remove pully and then all the metal clips with a flat screw driver and lift back portion of the outer drum up and remove. then the inner drum will be visable 9. take the 6 Torx (star) screws out of the drum support and remove! and semply reverse the process for assembly! taken photos of the process will help the assembly process as well
Was this instruction helpful to you?
Thank you for voting!