MAT10PSAAL Maytag Washer - Instructions

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.

Since my missus keeps her appliances like new, it behoves us to buy something of good quality when new. We did that. Now, after almost 20 years, the washer complained it needed new belts, which I complied. Tilted it up against the wall after pulling power cord. Removed both belts and replaced. Adjusted pump belt by loosening pump and then retightening. This is easy to get to by removing front (removing 2 philips screws). Piece of cake.

Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.

Replaced lid switch, but problem still continued.

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.

Tilt washer. Remove old belts. Put in new. Tighten transmission bet and pump belt per YouTube. It works like new now.

Viewed the very helpful video on your website, that spelled out all the steps to follow. The key point is to not forget the spanner nuts are left handed threads - even after noting that from the video, started the removal in the wrong direction, then caught my error and moved on through the disassembly process. In my case, I took time to deal with a lot of soap buildup cleanup in the outer tub, and even cleaned and put rust inhibiting paint on a few spots to try to get a little longer life out of the old machine. This repair cost far less than replacing it, and should get us several more years of service.

This washer was purchased in the early 1980s and is different from the one in the video and other repair instructions. You can recognize this earlier model by the agitator design. It only has the 4 paddles that start at the bottom and does not have the auger design on the upper part of the spindle as the newer ones do. While I was able to get the agitator to pop off by threading thin ropes under it and using a four-foot board as a lever, that was the end of my successful efforts. Even with the special tool and a five pound hammer, the lock nut would not budge -- even after overnight soaking in WD40. Yes, I did recognize the reverse threading. My next attempt would have been to heat the lock nut with a butane torch, but I gave up at this point and purchased a new washing machine on my way to pick up the torch. Would be curious to know if anyone else has had success with this older model as I saw other differences in the design that suggested that it may not have been compatible with this kit.

key to repair is to watch the video on mounting stem/tub seal as seen thru parts select. However, they use a nice new, clean,sanitized washer that may not reflect a 23 year old washer like mine. They give you the basics and it is invaluable to watch if you have never done this before. I strongly advise you buy a real spanner wrench made for your make. You may never need it again but it makes it much easier. Trying to use a punch or using a dremmel to operate on your large 'nuts' is, well, nuts! Get the wrench, just part of the cost of repair. See ebay. The first thing I noticed different between the video and my real life unit is the water hose connected to the washer, at the top of the tub cover. This did not exist in the video, but it is the way on my unit. So I did not disconnect it, just folded the top out of the way and tied it up. Then of course my real gripe with the video is that I have the old time band around the tub and the barrell, holding them together. They do not mate up very well and are not easy to put back together properly. In fact, installing the stem seals was easy and it fixed the original leak. I might add when you buy the replacement parts, you actually get 3 new parts. I suggest you use all the new parts in the package. You paid for them, you need them. Again the video only talks about replacing the very bottom seal, never mentioning the other parts they sold you in the bag. It is easy to figure out how to replace the other parts, they look like the ones you took off to get to the very bottom seal. Use all the new parts, regardless. So the only real issue is putting the band back on to hold the tub to the drum. We did not get it correct the first time and the unit would not spin, I had the top down too far. You could smell the rubber burning from the drive belt. They forgot to tell us about that!! Bums. So we loosened up the band, raised up the top piece and got it to spin. Of course, we did a large load, filled the water to the highest level allowed and when the unit hit the spin cycle, we got a leak from under the band. Thx video. To fix that we decided to never use the highest water level. So far so good. I can tell you the engineers failed on the design to mate up the cover to the tub. Other than that this can be done by us goobers, just take your time. And good luck. I must also thank my helper, neighbor John . for his added wisdom and support.

Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Slipped on belts no tools needed.

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.