SAV2655AWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joyce from Gary, SD
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
water leaking when washing
I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from New Lenox, IL
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
drain hose had water leak
remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SANDY HOOK, CT
- Parts Used:
- WP22002960
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
Bad tube seals and bearings
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Belleville, WI
- Parts Used:
- W10116791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Spin cycle became very loud
The instructions included were very good. The biggest problem I ran into was removing the inner tub from off the hub. Using PB Blaster was the trick there, but still took some effort to finally pry it lose without damage. The hub screwed right off after and removing the Triple Lip Seal was easy enough with screw drivers. Cleaned things up and replaced it by gently tapping around it to seat it evenly. Reassembly also went well, but I DO HAVE a story. Being as careful as I thought I could be, I still somehow broke the outer tub. I read about others experience, buying and using JB Weld WaterWeld to fix it. Now the washer is so quiet again that you have to look into the drain tub to see if it is spinning. AWESOME
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John W from Ashland, KY
- Parts Used:
- WP22004042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Blades broke from agitator
Parts where in, in a timely manner. I remover the fabric softener cup on top of agitator. User a 1/2 inch socket and a 3/8 ratchet with an 8 inch extension to remove the center nut. Popped the agitator out. Installed in reverse order, only tightening the nut slightly. The install went just like the video. Thanks much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Plumas Lake, CA
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
pump leakage
You tubed this procedure and it took 20 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- millie from hot springs village, AR
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
pump leaking water
remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from wadena, MN
- Parts Used:
- WP40045001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken idler pulley
knife to losen top, remove rear tabs securing top, unplug electical from timer and switches, unplug front door wiring, 2 bolts remove front, lift front pannel to remove. tape belt on drum on top. under drum you can see the belt around worn pulley. lift idler pulley assembly, remove belt from pulley, snap ring holds pulley in place remove woren pulley, install new, replace snap ring, restring belt. remove tape. spin drum to assure alignment. reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from rockford, OH
- Parts Used:
- WP27001126
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
twisted knob and broke plastic
pulled old knob off (removed metal clip left on) pushed new knob on .I am a widow so this was a big step for me to order part and replace but it was so simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Lynn, MA
- Parts Used:
- WP27001156
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Timer Control does not work
The first thing you have to do is remove the cover plate. And thing take a pair of long noise pliers to unscrew the nut that was holding the unit. And then carefully pop off the top off cover cap on the control knob. And then use a screw driver to push in the clip on each side that hold the knob in place it just plastic. And then carefully pull it off. And then go back to the back and push then push the unit to the right and then remove it out and that all to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Klamath Falls, OR
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
drain hose had a hole near wall drain.
The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terence from Nashville, TN
- Parts Used:
- WP22004042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator replaced
Used a socket wrench with extensions to remove agitator bolt and washer, removed and replaced agitator, reattached waher and bolt. Hardest part was realigning washer at bottom of agitator shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from The Woodlands, TX
- Parts Used:
- 22003428
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Mesa, AZ
- Parts Used:
- WP21001905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Fabric Softener Dispenser
pulled off the old & pushed on the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from huntington, NY
- Parts Used:
- WP27001126
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Took me about 3 seconds to replace the knob
Was this instruction helpful to you?
Thank you for voting!