MAH3000AWA Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sandra from Slinger, WI
- Parts Used:
- WP22003262
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
We had a leak in the tub pump hose
It was very easy...we ordered the part and it only took a day and a half and it was here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARILYN from SULLIVAN, OH
- Parts Used:
- WP22002162, WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
wouldn't spin out all of the water.
Replaced parts then the door wouldn't unlock, so we called a repair man and he's replacing the control board and the wireing harness, it cost 394.85 but the machine is in good shape so it was cheaper than buying a new washer and dryer, because I want them to match & the dryers only 7 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from El Cerrito, CA
- Parts Used:
- WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Would not go into spin mode
Removed 4 screws and door, lowered and removed front panel,removed screws holding locking tabs for the machine top, removed the four screws holding soap reservoir, lifted the top. Located under the lid and above the doorway I pulled out the wax motor retaineing clip with pliers and the wax motor, used pliers to remove the wire connectors, hooked them up to the new part and reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Rubber Boot between Tub and Door had a hole
When I looked up the part number, there was an installation video on the same page. I ordered the part then and there, and once it arrived, I put the iPad right on top of the machine and paused the video whenever I was doing the steps. It was TOO EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Davis from Sacramento, CA
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
door boot seal broke
I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauraine from Kimberling City, MO
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Started smelling rubber burning during spin cycle
I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Great Falls, MT
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Damaged bellow.
With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Phoenix, AZ
- Parts Used:
- WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Syphon cup had crack in it and had to be replaced
Syphon Cup is made one way and just slides into place...very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Scotts Valley, CA
- Parts Used:
- WP22004477
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Increasing water leak
The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Rochester, NY
- Parts Used:
- WP22003329
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Appliance repair company did a poor job and the motor fell off because of a missing isolator
I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Endicott, NY
- Parts Used:
- WP22003059
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
no drain, no spin
Unplugged, removed back, removed hose, removed pump. Reversed the order and plugged it back in. Walla! Do'n wash again. Parts Select is the way to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ryan from Troy, OH
- Parts Used:
- WP22003059
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
washing machine leaked out the bottom.
diagnosed problem (hole in drainage pump). unplugged, took service panel off rear, removed hoses, twisted pump counter clockwise. dropped new pump in, made connections, and it was good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E T from Milton, WI
- Parts Used:
- WP22002162
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Would not enter spin cycle. Found WAX Motor not cycling, 120VAC present when disconnected. Applied 120VAC dierectly cycled OK.
When I found the WAX motor would not cycle I applied 120VAC directly to the WAX motor and machine went into SPIN CYCLE as it should have. Stopped machine and ordered replacement Machine Control Board. Replaced the part and machine works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from yuba city, CA
- Parts Used:
- WP903115, WP22002988, WP22002263, WP22001948
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no spin
well I was hopen that it was less expensive parts but it was the big one control board. putting it in was real easy I love my maytag but its about 20 years old can wait to buy a new one I already pick it out the best maytag on the market its a nice and big one. I want to thank you for sending my parts so fast it all work out perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Parma, OH
- Parts Used:
- WP22003262
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leak in tub to pump hose
removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.
Was this instruction helpful to you?
Thank you for voting!