MAV4057AWQ Maytag Washer - Instructions

This was a very easy fix.....roll belt off....roll new belt on....seemed to help not sure if it fixed problem....might try pulley and bearing kit next

Unplug machine, lift about 6 inches to remove drive belt. Able to reproduce squeal by rotating pump pulley by hand. Remove front panel by using screwdriver to release retainer springs on either top corner about 1.5 inches in from corner, no need to remove control panel for this. Lift top panel to access screws behind front cover and remove (be careful here as sheet metal has sharp edges), lean front panel forward and lift off. Release hose clamps and remove from pump (hose clamp on discharge is spring type, channel locks work well here), keep towel nearby as there will be some residual water in the hoses and pump. Remove 3 bolts from top of pump to remove. Lift pump straight up to remove. Installation is reverse of removal, belt can be installed without tools (at least on series 10) as the motor pivots easily, place belt on transmission pulley first, then on pump and motor last this way you can pivot motor and slowly rotate motor pulley to guide belt on. Very easy repair, just take your time and you should have no problems.

First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

pop top,remove 2 screws,remove front panel.remove 2 spring clamps from tub hose.reverse!

A few youtube videos to replace the motor and belt. From there on out it was pretty easy. Separate the top from the spring clips. Remove front panel. Remove motor once inside and remove belt from underneath. After motor was out, Remove base from old motor and attach to new. Reassemble and voila. Good as new.

Unlike most videos, mine had a solid frame, no access panels. Following, is my disassembly & repair: I disconnected the water supply lines and drain hose. I slid the washer out into the center of the garage & removed the 9 base screws from the base plate. I slid the frame away from the base, leaving the working parts exposed. After pulling the working mechanisms from the outer frame, I turned it (drum, transmission & base) upside down. I used a pair of vise grips, pinched them onto each spring & removed them, using a downward motion it was a lot easier. I placed the base plate aside, removed 3 opposing screws holding the snubber ring & put 3 longer 8-32 screws in to hold the brake assembly. Then I removed the 3 remaining screws, lifted the plate & replaced the ring. Then I reversed the process, replacing the old springs with new ones & finished the job in about 2 hours.

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

used video provided on repair procedure.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

As described in video; however, the video does not match the model I repaired. Most stuff is the same. Hardest thing to do was installing the new springs on the back of the tub (2 of them).

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.

Shut-off water + power.With the putty knive; slide it under the front of the top to push back on the spring clips.The top will lift easily and it is hinged.The Water inlet unit in the back has a plastic cover.Remove carefully.One screw holds the unit in place. Remove and the the unit will slide out to the left. It's now easy to disconnect the hoses from the unit. The wiring to the coils is color coded,take note for proper reconnecting. Remove stakon connectors from the valve coils. Careful, do not pull on the wire but wiggle it of the coil connection.Pay attention to the routing of the wire harness. Also the kit comes with a clear plastic splash shield. make sure the new goes in the right place.Now the old water inlet valve can be removed from the metal bracket.One srew.Assembly goes in reverse