MAV7260AWW Maytag Washer - Instructions

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

I knew it was the belt because of all the noise it was making. I ordered the belt and it arrived real fast. I pulled the washer away from the wall and tipped it back at about a 45 degree angle against the wall so I could get under it. I propped it with a bucket. I then pulled the old belt off and spun the new one on. Real fast & easy.

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

I'm not a washing machine technician but I did nurse a new Kenmore machine for 23 years and was ready for a replacement. Craigslist advertised a Maytag I was interested in and I bought it with the seller's assurance that it worked perfectly. It didn't and I went online to try and figure out what might be wrong. Clearly, the tub was traveling beyond it's design limit and I suspected a spring or two might be involved. Somewhere online, I found the illustrated parts diagram and then went looking for additional information. To my extreem delight, I came across a do it yourself repair video that demonstrated the procedure well enough that I was completely confident I could make the repair with little effort. That video was one of several service related appliance videos offered for free throughhttp://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/index.html/ The final consideration was whether I could buy the replacement suspension springs and snubber ring for less than I paid for the washer. I found PartSelect and within minutes, I had the parts ordered. The parts arrived within 4 or 5 days, as promised, well packaged and in perfect shape. This morning, using the video as a final reference and the new parts, I completed the repair with only a minor hitch. Without the special spring tool used in the video, I struggled a bit with getting the new springs attached. That's where my wife came in handy (after all, she was movitated). Having her tilt the drum toward the spring landing made it much easier for me to stretch it into place using an adjustable locking plier. I actually enjoyed the whole procedure.

My Maytag Atlantis MAV7550AWW does not have a side inspection door like many have posted. After taking most of the washing machine apart I noticed in the front between the top lid and the main body there appeared what looked like some type of clips. I used a butter knife and pushed the V clip back and the one side of the top lid was released. After doing the other clip it was clear that was how to access the motor etc. After the top was open, it's hinged by a plastic hinge, you will need a small wrench and have to move the tub to the side to take off two small nuts also in the front. 8mm I think. Then the entire front of the machine comes off and the pump was right there. Time to remove and install the new pump was 15 minutes. I replaced the belt at this time also but had to lay the washer on it's side. Put the belt on two of the pulleys and pull hard. You will see that one of them is a spring held tightener. I did this outside on the deck as you will have water in the hoses and pump. After all was hooked up I ran a wash cycle only to hear that screeching sound was still there. My best guess is that it's a tub motor going. I am just going to use the washer till it dies then get a new one.

Opened the lid and snapped hinge in to place. The part was an exact match and the job went flawlessly.

I popped off the fabric softener on top of the agitator. Used an extended arm on my socket set to remove the only nut holding the agitator on the motor assembly apparatus. The agitator came off with ease. Just reversed the procedure in replacing the new agitator. This was an easy job.

unplug cord,disconnect hoses,pop front clips,swing up the top,unplug wires,unscrew bracket with valve,replace valve and reinstall.I did replace hinge because I pulled up to hard the top.

Removed the old part with a screwdriver & installed the new part. It took approximately 2 minutes.

very easy replacement. was probably broken for a year and only took five minutes to replace. Can't believe we waited so long!

Removed the old hoses and screwed on the new hoses.

As for how I did the repair , I just followed your instruction video . The instruction video provided by Part Select was very very valuable.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.

I also really like you list of probable solutions to the problems with the machine.

My wife is now happy with her washer again therefore I am also happy.

Thanks so much.
I can see me being be a loyal customer for many years to come.

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.