MAH3000AEW Maytag Washer - Instructions

This is an easy fix once you see how it goes together but can be a little difficult in certain steps. I first Removed the door at the hinges and removed the screws on the side securing the liner. Once the liner was removed you can see what pieces are involved and how they go together. Take pictures before removing any thing, you'll need them during the repair. I removed the vent tube and the circular thing with springs. Transfer the circular thing first noting the screw slots. The next step may be a little difficult to see how the upper vent tube bracket slides off and how to maneuver the springs. The whole unit comes off as one so don't take it apart. Make sure you know how it goes back on with pictures. I found using channel lock pliers to compress the site springs was the best as it was easily attached on the new panel while compressed. The vent tube with the rubber seal on the bottom was tricky but you can finesse it in place. Once together putting the door together and back on the unit was easy, Worked great and saved a ton of repair money.

I visited several web sites looking for repair parts for my Maytag washing machine. Your site was the easiest to navigate and provided great diagrams and pictures to ensure that I purchased the correct part. I liked the ability to track the delivery of my parts via your web site. I received my parts within a couple days.

Unscrewed the 4 screws of the old bezel; lifted the bezel out; moved the lid from the old bezel to the new one; set bezel in place and screwed it in with the old screws. Looks and feels like new.

Removed the broken plastic bezel and lid assembly. Removed the lid from the bezel by flexing the lid so the hinge pins would clear the mounting holes. Attached the old lid to the new bezel and reinstalled the assembly with the four existing mounting screws.

The repair was easy and for about $15.00 total the soap dispenser is back to new condition.

It was easy as 1,2,3. Took the old knob apart and replaced it with new one. About 20 minutes.

the pictures on your web site allowed me to positively identify the 2 pieces quickly and surely. replacement was a snap and took less than 2 minutes. Thanks!!

Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.

Removing the gasket was very easy. A couple hints on installing (1) attach the gasket to the drum first!! this is the trickiest part but once you get it on, attaching the cable and spring was fairly easy (just used two people and a pair of needle nose pliers). Once you get that on, "lube" up the other side with soap to make install easier.

Ordered siphon cap according to FPS parts list. Wrong cap, but I don't care! Customer support was so helpful and willing to do everything to get me the correct cap, to include refunding my purchase price AND shipping before I even sent it back. They will be my first choice for parts in the future! My husband is a "fix it" guy, so I know that will mean a lot of purchases. I look forward to future business with this company!

With a torn boot on this front load washer, (nails in the pocket of my jeans) water leaked out on the floor with every wash. I knew it would cost a fortune to get fixed, so I decided to try it myself. I can take anything apart!
I heard of Parts Select.com from a friend and checked it out. With their help, I found the model and part and just ordered it. It was easy!
When the part arrived, I was obligated then to do something!
Since this is a stack unit, with the dryer on top, I thought I would take the dryer off and try the repair from the top. But there was no way that dryer was coming off! I tryed every screw and it wouldnt budge.
So I saw two screws in the front and started in on the washer below. I was careful to make notes on how I took this machine apart so I could put it back together!
I got down to the drum with a spring close guywire that holds the boot tight to the drum. It came off easily and I took the old torn boot off and put the new boot in place.
The tough part was getting that guywire and tight spring back on! The lip that holds the boot to the drum is very shallow and the book would not stay on all the way around and allow me to string the guy wire around in the little channel without coming off. FRUSTRATING!
I improvised and used duct tape to tape the boot to the drum to keep it in place so I could string that wire around. Man, did that take some doing!
I managed to get that wire around with the help of the duct tape, but the second big challenge was putting the spring on, as it was under alot of tension. It was tough to puuuuuullllll it together without pulling the boot out of the channel I had to duct tape it into!
By the grace of the Almighty, some prayer and some cussing (forgive me Lord), I got the spring into the rings on both ends of the guy wire. VICTORY!
Putting the boot front back in is easy, just put it into the holes that receive the projections under the front of the boot. No problem.
After all that, putting the washer all back together was a cinch!
And....
IT WORKS!!
I did it! No more leak! No expensive fix it job!
I did it myself, am prouder than heck!
Oh.....
No more Nails in the jean pockets!

My husband completed the repair by himself. He said that the "string trick" was helpful.

Used the conversion kit to replace both parts.Note the supplied instructions say to test the install by running a spin cycle before you put the door and panels back on. However the unit will not initiate a spin cycle without the door lock engaged. Not just the light switch, the actual door lock mechanism. You have to reinstall the door, then test. This error in the instructions cost me about 30 minutes.

Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!

removed one panel and front door to access under tub.leak solved!!!! thanks

removed door,Opened the front panel, opened the top and proped it out of the way. Pulled the boot from the front cover disconnected the drain, released the boot clamp and pulled the boot off. I cleaned the inside of washer and soap tray. cleaned debris from the drain hose. repaired a broken soap dish connection. changed supply hoses and new valves. Generally checked cleaned and overhauled the washer.