LAT9356ABM Maytag Washer - Instructions

took washer into the garage, removed front cover & disconnected the wiring. Then i removed the motor assembly. Piece of cake to finish job.

I opened the front of the washer by removing the 2 screws on the bottom front of the washer, then swinging the front upward until it was clear of the hangers at the top. The hose sits right in front. It was cracked where it attaches to the tub. I loosened the hose clamps at the tub & the pump with a nutwrench & removed the old hose. I slid the clamps onto the new hose & put the hose on to the tub & pump. I tightened the clamps, reinstalled the front & was finished.

A tension sping on the motor broke, smoking the drive belt.
step1...remove front of the washer to access spring, tip washer back & prop on short 2 x 4 board. 5 minutes
step 2... remove one end of pump belt to get new bely up to drive pulley put on belt using fingers only & replaced the end of the pump belt....2 minutes

step 3...put new spring under motor & hook one end in attaching hole on motor, reach through with pliers to grasp spring to pull end to attach spot on base...1 minute

It took longer to open up the washer front & prop it up that it took to repair it. This is a siper easy repair!

Disconnected power to washing machine then took off back panel. Located "Lid switch", disconnected lid switch wires, pushed lid switch toward front of machine to remove.. then replaced with new, reconnected power wire to lid switch, reattached back panel, plugged power back in.

First I removed the two screws that held the front panel in place. Then I determined that the belt for the pump had fallen off because the drive belt was worn (and inverted) and a piece was hanging off and causing the pump belt to slip off the motor. I replaced the belt for the pump (Temporarily) to allow the tub to drain.

I replaced both belts with new belts and returned the front panel. The process took 15 minutes due to the necessity of explaining the proper use of tools to a neighbor child and allowing him to assist (required for the completion of one of his Cub Scout requirements).

I turned off the water at the main water inlet. I then removed the hose connections to the valve inlet. I removed the one screw on the plate pulling allowing me to pull the plate out from the washer body. I then removed the wires connected to the old valve placing them on the new valve (so not to be confused). I took off the small hose clamp attached to the valve. I removed the valve from the plate and attached the new valve placing the a new hose lamp on the hose (wires were already attached) screwed back to the plate in the washer body connecting the water lines and turned the water on at the main valve. I did have to run to the hardware store for the small hose clamp but that was my choice to replace the one that was existing. The washer now works like it is new.

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.

1st We pulled the washing machine from the wall and unplugged it. 2nd We tilted the maching back against the wall so that we could see all the pullies. 3rd. We removed the two screws that afix the front panel on the lower part of the washing machine and removed the panel. 4th We removed both belts and put new belts on. 5th We put all parts back in place and plugged maching back in, slide it back in place. 6th It worked like a charm and I proceeded to wash 3 loads of laundry that evening. The only tool we needed was the phillips head screw drive to take off the front panel. It took us 5 minutes to fix the machine.

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

Well, I figured out a couple of things during this process. #1 The Washer was smoking. It had happened before (a sock got suck between the basket and the tub) so I assumed that happened again. I couldn't see anything in that space this time, so I dissasbemled the washer to see if any clothing was there. Relatively easy once finding the screws to remove the front panel. #2 What I found was a sock in the pump box. I disconnected the hoses and removed it, saw nothing between the basket and tub and ran it to see if problem corrected itself. It still was smoking. That is when I checked the belts, #3 first the pump belt, replaced it, very easy, just pulled the old one off, and wheeled the new one on. It still was smoking, #4 so I replaced the drive belt, very easy and the same as the pump belt. It still was smoking so I lubed the wheels for the belts, and #5 cleaned the residual rubber around the wheel from the old, fried, dry rotted drive belt. No more smoke!!! However #6 remember to leave space between the basket and the top of the tub, as when I put the washer back together the basket didn't spin. I removed the top and ran the spin cycle, it spun fine, reconnected and it didn't spin, the tub top was touching the basket, that's when I relized the top was on too tight. I reattached and left about 1/4 in of space and all is well now.

Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Checked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.

Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

Thirty year old Maytag washer. Remove two screws at bottom of front panel with Philips screw driver. Hinge panel up to disconnect front panel from top of machine. Tilt washer back against wall to gain access to pulley at underside of washer. Then remove Philips head screw from bottom of center shaft. Remove bevel washer with screw. Remove stop block from end of center shaft and wind the pulley off center shaft. Clean center shaft of any debris and lightly coat with grease. Install belt on new pulley and motor, wind new pulley on center shaft. Replace stop block, washer, screw, and front cover.

Hardest part was figuring out how to access the internals (not through the back or the top) It turns out there are two screws on the lower front of the machine, not easily found, which when removed allow the front panel of the machine to swing to front and out of the way allowing full access to the internals from the front. The water was comming from one of two water pump hoses. The hose was held in place with 1" hose clamps and was easily changed out.

Unhooked H and C water lines. Removed cover plate with control valves. Pulled power wires off solenoid valves. Remove exit water hose clamp then hose. Put new valves on in reverse process. Checked washer through cycle to see it worked all OK. Had to make new mount ro install valves.