SAV5300AWW Maytag Washer - Instructions

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

Ipulled the front panel off and found that the brake pads had broken into pieces, ordered new pads. Two of the pads were accessed from the front of the machine and were relatively easy to replace by removing the two attaching bolts, spreading gap in area that they fit into with a plastic pry tool. I gained access to the third pad by removing the punch-outs on the side of the machine (circular). If I had not had these prepuched pieces available to me I would have simply cut an access hole in the rear of the machine with a jig saw, (who will ever see it).

Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks

Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!

I first ordered the parts and to my dismay, I ordered the wrong belt for the spin belt. I called customer service in which received an Return Merchandise Number and ordered the correct belt. PartSelect was prompt on sending the correct out by FedEx, thank you for an excellent experience.

Laid washer on its side and had to remove the motor,replaced the pulley and belt replaced the motor and put all parts back together washer spins and runs like it did when it was new.we did not need the screw or nut but did not know when ordering parts

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

I read what the others had done and thought it was the lower bearing so I originally tore it down and replaced just the lower bearing.

Unfortunately, after 2 + hours of doing that and putting it back together, it still didn't fix the problem. So I read more reviews and others claimed to use this kit and that it fixed the problem. So I ordered the kit.

BTW, Parts Select rocks!!!! They get me the part within about 2 days every time.. Great Service! Thanks guys!

Anyhow, part came in, knowing how to tear this thing down now, I was able to get to where I needed to be within about 45 minutes.

2 things that were difficult.

The first was removing the plate at the bottom of the tub. This is the aluminum plate that looks somewhat like a spoked wheel. Maytag has a tool for this. Without it, you must go at it with a small punch on one of the spokes and carefully tap the seal until it turns. You may have to try it from different angles to loosen it up but it will eventually give way..

Once you get that off, the second little piece of joy is actually removing the seal from the bottom of the tub. Here again, Maytag offers a tool to remove this. Without it, and with years of this rubberized fitting mounted in this plastic tub and corrded with water and crap... you will need to create a bearing puller.

I did so with a 2X4 board straddled across the bottom of the tub. I used an 8 inch lag bolt, drilled a hole through the 2X4 and placed the lag bolt throuigh the board and through the center of the bearing. I attached a large washer and nut to the bottom side of the bearing and then began to tighten the bolt on the other side of the board. By tightening the bolt, the board created alot of tension but not enough still to seperate it from the tub. With the tension on the bearing, I turned the tub over and tapped it with piece of wood the size of the bearing and a rubber mallet. It popped right off. The rest was just reassembly.

Don't forget to remove the sticker backing on the felt gasket to hold the gasket in place while you screw the tub back together...

The good news... Super quiet! So, about 3 hours.... (I had to come up with the idea to remove the bearing and build it) and it's all done..

Yeah.... Fun Saturday.

I had previously done a partial tear down on the machine to see if I thought I could do the repair. The dealer try's to scare you with warnings about special tools etc. Looked OK and after reading other comments on this site, I thought I would try. The only comment that I would add to what has already said is that you should have the recommended sealer or an equivalent sealer. I used weatherstrip adhesive that I had on hand. Hope that it holds up! Like it says in the directions, the seal will lift up if there is too much sealer under the lip of the seal. Just hold down the seal with a weight until the adhesive sets up and then it will stay. I've fixed cars for 30 years and this was an easy repair comparable to replacing wheel bearings.

I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.

checked for unbalanced load. still banging. removed lower front panel by removing 2 screws. then removed front top panel- 2 more screws. turned unit on spin cycle to see what was going on. this is dangerous as many moving parts are exposed, so keep everything clear. banging was the tensioner slamming back and forth. unpluged washer from outlet and felt along the belt to find part of the 'v' shaped balt had come part, leaving a gap in the "v". ordered part.when i got the part, i removed 4 larger bolts that held the motor, pully, and pump. i unplugged the wires for the motor, and removed the belt from the bsket side pulley assembly by slipping it off and under the shaft. i removed the torx screws that held the pump on the motor and removed the belt. PAY ATTENTION to how the belt was in between the pully and pump assembly or you will have to remove and redo it. reassemble the pump over the belt, pully, motor, and put the belt on the drum side pully before bolting it to the washing machine. it is fairly heavy and tight, so you might need help. this was not hard and you do not need to take apart the washer except for the two front panels and the motor assembly. i just pulled the unit away from the wall and tipped it back to access the inside. take your time and pay attention, and make sure it is not plugged into the wall and you should be fine.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.