A310S Maytag Washer - Instructions

My washing machine would only run hot water. Told my husband and we were ready to call the repair man when I suggested we try to order a part. So I Googled "washing machine repair". Clicked on the first sight I saw and 'searched 'no cold water' amd immediately saw explanation of our exact problem. The solution explained that MOST of the time the problem was the water inlet valve. So I ordered the part. My husband put the part on the machine and the process would have taken less than 10 minutes however the clamp was so rusted to broke and that required a trip to the hardware store. But I suppose clamp-life does not exceed 20 years. So mission accomplished and a great big thanks to all those who explained what they did to solve the problem!

I unscrewed the bottom two front phillip screws. Lifted the front panel at a right angle then popped off downward. Used a 3/8 socket to unscrew the two screws inside in the upfront corners holding the top to the sides. Pulled off the top bleach line.
Lifted the lid upward until it rested on the back wall. Unscrewed the water fill tube connected to the top side panel which to reach the inlet valve area. wrote down which color of the four wires went where. Unscrewed the back plate and disconnected the valve wires. Reversed procedure for installation. Cleaned other parts while I was in there. Installation went quick and smooth.

First I unplugged the power cord from the wall. Then I turned off the water supply shut-offs at the wall and removed the hot & cold connections at the rear of the washer. Then I removed the two screws that held the assembly in the rear of the washer. I then pulled the assembly out about 3-inches, marked the new assembly to show the proper color of wire for each lug and disconnected the four wires at the lugs. I disconnected the rubber fill hose from the assembly and removed the assembly. Next, I installed the new assembly in the reverse order. It worked fine without any leaks & saved me from buying a new washer. My old washer now gets my clothes cleaner than it has for years - much quieter and quicker too.

took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you

Partselect.com gave me a very helpful list of parts per symptom. Said that there is an 88% chance that belts were my problem. Since the machine is 200 miles away I ordered two other parts as well. Belts fixed it! Took front cover off (not totally necessary). When the machine is tilted back belts are exposed underneath. Two belts later I was up and running. This site is really great.

Pull washer out from wall. Remove front panel (2 Philips head screws), swing bottom of panel out, remove panel. Tilt washer backwards, lean against wall to expose area under washer. Roll off old belts, roll on new belts. Move washer back upright, replace front panel, replace the philips screws, move washer back to original position.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

I followed the instructions on this website to a T. You can take the front cover off and you will notice a small drip from the tub area where the Hub bearings (above the tranny) meets the washing tub. Once you've identified that the leak is indeed coming from that area and not a loose tube. Allow the washer to complete the job and drain the water. Then simply unplug washing machine before starting the process of the repair. It is very important to remember that you must have a spanner wrench before attempting to perform this repair. keywords=spanner+wrench came within two days with Prime Shipping. Also be sure to order the replacement parts from this site. It takes about 3 days to arrive however so be prepared to be without a washer for a few days. Other than that just follow the instructions provided and there is a very good step-by-step video on this site .

Could not repair. The gearbox on the agitator was broken and that kept the agitator from working. Do not assume it is a belt problem on a washer built in 1987.

Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.

I removed the screws holding the Elbow in place. Removed the broken pieces and replaced them with the new part. Maytag gives great access to the back of the washer so I could easily bring the part into position to replace the screws that hold it. Worked like a champ!

After removing the front cover and tilting up the top of the washer housing, the area of leakage was obvious. I unscrewed the clear plastic injector housing, loosened the clamp, slid the hose off of the clear plastic injector housing, and removed the plastic injector nozzle and the rubber injector valve.

I then order the plastic injector nozzle and the rubber injector valve. After the parts arrived, I simply put things back together, and no more leak!

Note: When putting the plastic injector nozzle into the rubber injector valve, I used a little liquid detergent as a lube.

Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.

First thing I had to determine what was wrong. The machine had worked admirably for a 1980 model but over the last few years cold water input had reduced to almost nothing. There was also a slight hum during filling but it had been so gradual I really didn't recognize it as part of the problem.
After checking that the cold water faucet, hose and screens were okay I removed the front panel to see how water flowed inside the machine. I suspected the inlet valve on the machine was not working correctly so I looked on PartsSelect and found similar repair stories. I ordered one and it arrived in 2 days.
Repair was simple. Turn off hot and cold water and disconnect hoses from machine. Mine were on snug so it took pliers to get a turn started. Lay them in a pan to catch drippings. On the back remove the single nut above the inlet valve and lift to remove the panel. Remove the two mounting screws for the inlet valve. If needed rotate the electrical connections on the new inlet valve to match the old and transfer the wires. Remove the small output waterline and transfer it to the new valve. Mount the new valve to the panel and resecure the panel to the machine. Snugly attach the hot and cold water lines. Turn on the water and after checking for leaks you're good to go.

The repair itself is fairly simple. However, being 65 years old getting the new valve back into the back opening of the washer and screwed in was a challenge. The clamp on the water connector hose broke and I had to drive to the store to replace it. You may want to consider giving a heads-ups option of ordering hose clamps to DIYers, when you go to order. Also, the instructions that came with the part was not totally accurate. I had to rotate the cylinders outward to connect to the electrical points. But, my machine is pretty old and that may be why. Otherwise, I am very pleased with how quick I received the part and it was exactly what I ordered. My washing machine is back in business. Thank you