A103 Maytag Washer - Instructions

Loosen one hose clamp, slide old hose off fitting, disconnect hose from washer tub. Apply liquid soap to both ends of new hose to make it easy to slip onto the fitting and the tub. Slip hose clamp on one end, fit other end to washer tub, slip hose onto fitting, tighten clamp.

Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

opened washer removed old damaged part and replaced with new part, losen brackets from hose inlet, removed hose, then fit new hose into tub groves can be very frustrating take your time and be patient, once you get it on, fit over inlet, tighten brackets make sure that seal is secure by turning on the water to fill if no leak the job is done run thru complete cycle to test. Thanks

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor
Removed motor and slide
Cleaned and replaced slides and greased put back in washer secured
Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done
Great instructions that came with parts

all went well until testing. tub level did not shut the water off, caused a spill

Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

I removed two screws near the bottom of the front panel and removed the panel by pulling the bottom away from the machine. Inside, I removed two cap screws, one under each front corner of the top panel. The top panel is hinged at the rear. I lifted the top panel from the front, rotated it to the rear and leaned it against the wall behind the machine. It was not necessary to disconnect any wiring. The "U" shaped water injector hose connects to the washer water source with a hose clamp and has a grommet-like end that fits in a round hole in the top of the tub. The hose had cracked and was leaking where it connected to the tub. The new injector hose was a direct replacement and was easy to install.

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..