MAV6300BGW Maytag Washer - Instructions

Pop the cap off the agitator/auger no tools needed. Once removed select a socket and a socket exstension. remove the screw amd pull off the part. Make sure to save the washer that may be still attached to the inside of the agitator. install the new agitator using the existing screw and washer. Takes about 15 minutes.

First I raised the top and took out the two screws that held the front on. Then I removed the back panel which were held by 4 screws. Then I turned the machine on it side and removed the belt. I then pulled the hose off from the tub to the water pump and the small hose on the back of the tub. I then removed the 6 springs that held the tube to the base and then I picked the tub up and turned it over on the floor. Then I backed off on the screws that held the snubber in place. I pulled the old snubber out, retighten the screws that held the snubber tight. Then I reversed my steps.

After taking the motor off (it looked loose to me!) and stripping out the bolts on it, then finding that the bolts holding the motor were permanently affixed to the motor (and they were an odd size not available at the hardware store), I drilled the bolts out and put in new ones (on the motor) and re-affixed the same. I still had a problem. I then went online and found that most people had problems with the water pump. I looked at the pulley on the water pump and found that the inner shims had slipped out on a permanent part (and could not be put back in with the basic tools I had on hand). I ordered the pump online, and replaced the same. Took about 30 minutes after I found the real problem and got the parts in. My pump had a permanent metal disc on the bottom which did not come with the new pump, but the new pump fit without it. Machine works fine now.

I removed the old pump put the new one in its place. In twenty minutes i was ready to was clothes. It was so quite i thought something was wrong. I received the part in three days the timing was great.

As described in video; however, the video does not match the model I repaired. Most stuff is the same. Hardest thing to do was installing the new springs on the back of the tub (2 of them).

Removing and installing the pump is theoretically easy, as everyone on this site has said so far. Just remove three hex-shaped screws, loosen drive belt and remove pump, then install new one using the same steps in reverse order. The trick is getting the screws off and on--they do not have slots for a screwdriver and there is not room around them for a socket wrench or pliers. I probable spent over an hour just on removing/replacing these screws and have many bruises to show for it. I ended up attaching a vice grips on the tips of the screws underneath the washing machine and screwing them out that way. And replacing the drive belt was horrifically difficult--that's where the other hour went. The devil was definitely in the details! If anyone had told me what I would have to go through to make this repair, I would have called a repairman. And I am an extremely handy person--I do stuff like repairs all the time, so it is unusual for me to say this. The good news is that the new pump works and the washer is back in commission.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Followed the great instructions on your video

Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

Took off back cover an belt replaced part

I watched video, couldn’t believe how easy to replace

After receiving the new part, I lifted the lid making sure it was level, then simply pushing the new pin in the lid hole, then pushing the whole thing back toward the corner of the lid until it clicked in.

Removed front panel from washer,removed belt, used 1/2 inch socket setand channel locks to remove hose and pump. Installed new pump, reinstalled hoses and belt, and placed front panel on machine.