MAV7358AWQ Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hersch from Mamaroneck, NY
- Parts Used:
- WP22003062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace power cord that had burned from a small fire
I removed top control panel and then the old power cord that been damaged by a small fire and the just attached the new power cord and control panel. Unblievably simple and I saved myself a lot of money. Where I live in a NYC suburb this type of simple repair could easily cost $100.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from WINTER SPRINGS, FL
- Parts Used:
- WP35-6780
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
1Loud Reaking Noise During Pump Cycle
Removed front panel from washer,removed belt, used 1/2 inch socket setand channel locks to remove hose and pump. Installed new pump, reinstalled hoses and belt, and placed front panel on machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from bremen, OH
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
washer wasnt spinning out water and making noises
i removed 3 screws from back of washer , took off 2 hose clamps , then i took 4 screws out of waterpump, removed belt . put new pump on very easy. thanks part was perfect, fixed problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marylou from Old Forge, NY
- Parts Used:
- WP21002026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Noise
I changed the piece easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from SANTA ANA, CA
- Parts Used:
- WP21001950
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washer shaking and shutting off
Repaitmr was simple. Followed video instructions from web site. Problem I ordered wrong motor so it just blew my plugs fuse. Also needed pump. Changed motor to old motor installed new pump. Machine works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Needham from Leesville, SC
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Spin cycle out of Balance - Machine walks from wall
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from LAWRENCEVILLE, NJ
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn't spin after rince
Followed the great instructions on your video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wading River, NY
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set
noisy out of balance during spin cycles
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Hollywood, FL
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Pulley Insert Coming Out Of Pully Hitting Housing
Replaced pump because pulley did not come off pump without breaking pump in half.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hollee from Rancho Mirage, CA
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer making loud noise and tub off balance
I followed Gary from Sioux City IA instructions. Very well explained.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Mount Vernon, WA
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The water pump was making a horrible grinding sound
The repair was a piece of cake! I actually stumbled upon PartSelect by searching for the part, it happened to be that the part through your company was the cheapest! Not only did that make me and my wallet happy the part came fast and i was able to repair the washer in 15-30 mins!! Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julio from Oviedo, FL
- Parts Used:
- WP35-6780, WP22002239
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bad Water Pump and clip holding front panel
Replacing the water pump only required the removal of the front Panel, removing and replacing the pump with socket set and then installing front panel with the new clip. Once this was complete the belt drive was installed on the bottom of the washer. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doreen from Seaford, NY
- Parts Used:
- WP21001905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dispenser did not come with maching
All I had to do was take off the white cap on top of the spinner, place the dispenser cup in the hole and it was done! It works great even though there was no indication that my model would work with a dispenser. It was the best $3.95 I ever took a chance on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Oxford, MI
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High pitched squeal on rinse
Tipped the machine against the wall. This exposed the belt which is not inside the machine. Took the old belt off put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- valerie from put-in-bay, OH
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washer wouldn't spin fast enough.
Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!