PAV3200AAW Maytag Washer - Instructions

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

Unlike most videos, mine had a solid frame, no access panels. Following, is my disassembly & repair: I disconnected the water supply lines and drain hose. I slid the washer out into the center of the garage & removed the 9 base screws from the base plate. I slid the frame away from the base, leaving the working parts exposed. After pulling the working mechanisms from the outer frame, I turned it (drum, transmission & base) upside down. I used a pair of vise grips, pinched them onto each spring & removed them, using a downward motion it was a lot easier. I placed the base plate aside, removed 3 opposing screws holding the snubber ring & put 3 longer 8-32 screws in to hold the brake assembly. Then I removed the 3 remaining screws, lifted the plate & replaced the ring. Then I reversed the process, replacing the old springs with new ones & finished the job in about 2 hours.

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

used video provided on repair procedure.

On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

unscrewed screw holding old actuater in and replaced it whith the new part.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom

The repair was easy. I had to unscrew on bolt, place the agitator assemply on and screw the bolt back down. Simple , Sear was gonna charge 175.00 just to ship the part. I got the part for $57.00.

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..