MAT12PSDAW Maytag Washer - Instructions

Since my missus keeps her appliances like new, it behoves us to buy something of good quality when new. We did that. Now, after almost 20 years, the washer complained it needed new belts, which I complied. Tilted it up against the wall after pulling power cord. Removed both belts and replaced. Adjusted pump belt by loosening pump and then retightening. This is easy to get to by removing front (removing 2 philips screws). Piece of cake.

I removed top control panel and then the old power cord that been damaged by a small fire and the just attached the new power cord and control panel. Unblievably simple and I saved myself a lot of money. Where I live in a NYC suburb this type of simple repair could easily cost $100.

Tilt washer. Remove old belts. Put in new. Tighten transmission bet and pump belt per YouTube. It works like new now.

We were not sure if the problem was the belts since they were not completely broken or overly worn down, but decided to try to put new ones on given the burning rubber smell and some light smoke coming from beneath the washer when it was on the spin cycle and the drum would not spin. We found some how to videos online and through the part select customer experiences, we ordered the belts and got them within 2 days. We put the new belts on, which is fairly easy and quick to do with the proper tools once you get the front panel of the washer off. The new belts seemed to have done the trick, as the washer began spinning again with no odd sounds or smells once the new belts were installed, and it has been running great so far. I highly recommend ordering from this site, as the parts are the real factory parts and are easy to find an order based on your appliance model. I found the pricing and convenience, as well as knowing the parts would be right and the best quality, to be the best part of this site, as ordering from other online retailers may land you with the wrong parts or kits with parts you don't necessarily need.

Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks

Slipped on belts no tools needed.

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

befor start i make sure whether i can repair or not.then i order the part which is fit with what i wont to repair.by checking siriel number . then repairng is very easy.

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .

Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.

Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.

Received wrong springs for my model had too use combo old spring with the two new (too long) springs to get the tension on the belts. For now it working. Did not contact you due shipping took so long and two delay date change by FedEx ground. I didn't want to go thru another delivery nightmare. Thanks for the time.

I first removed the front panel of the washer and removed 2 screws holding the top of washer in place. I had to flip the top up. This allowed easy access to the tub. I then removed the agitator by removing the set screw on the lower portion. From there I loosened the mounting securing device by using the nail punch and hammer inside of the tub (it was loosened by turning it clockwise). The tub was now loose and I removed it from the washer. Next I removed the torx set screw and the tapered hub unit (cork on it). It had to be again loosened with the hammer and nail punch and turning it clockwise. This exposed the part that needed to be replaced. I replaced the old with the new and the washer now works great with no leaks! Be sure to clean everything you remove that will be reassembled.

The PartSelect video was awesome in giving me confidence. The step by step instructions worked well until....

Calcium carbonate buildup on the reverse threaded spanner nut locked it in place such that I couldn't break it free.

I tried muratic (hydrochloric) acid which removed the surface scale nicely. But, no impact on allowing the nut to be pounded free. I then used a dremmel drill bit to vertically drill holes into the nut cross section. This allowed me to tap in a cold chisel and then pry the nut apart. Unfortunately, I had to repeat this for the second spanner nut as well.

Note, the first nut threads on the second part of the tub seal kit. So, drill away. You will not need these threads. however, the second set of threads you need to be carefull not to mess up. By drilling verically you can remove most of the cross section and cold chisel the rest without damaging the shaft threads. Second note: gently tap /wedge the cold chisel into your drilled out area. you don't want to hit hard and risk the ball bearings/raceway from getting ruined. Use the cold chisel to pry apart the aluminum stem hub. Its cast, so it will break pretty easily.

Net, the video allowed me to complete a project that exploded views, etc. would never have! The frozen nuts aside, this was an easy job that WORKED! No more leaks.

I viewed and followed the PartSelect Instruction Video. My only problem was reattaching the door after the hinges fell off.Everything fell into place as the video indicated. After I regrouped I was able to put the hinges back and then I was able to reattach the side panel very easily as the vedio indicated. Thanks for everything.