LAT9904AAE Maytag Washer - Instructions

I thought it was going to be next to impossible to find a replacement part for an older washer. So my first attempt was to try to epoxy the original part, but the epoxy didn't hold up to the stress. I began thinking about what I might need to make a replacement part which was possible but not very practical. Although I dreaded trying to find this part online, I was very surprised and elated to happen upon PartSelect! Oh, by the way, this washer belongs to my daughter and I nave tossed the paper I wrote the model number on, so the model number was entered as the part number, sorry. At any rate, the the part was reasonable priced, and shipping about standard, but I still saved a lot by doing it myself rather than having a repair person for something this simple. Partselect online lookup made it easy to find the model and drawings to help me find the correct part nomenclature. AND, the part was in stock! So I am pleased with how this venture worked out.

Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.

Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.

Power cord out, of course.Popped off the front panel, swinging bottom outward. Wedge shaped protrusions on top of front panel work as a hinge until the bottom is swung out and the entire front lowered. Unscrewed the top--one screw in each front corner accessed from the front opening (removed panel). Panel behind control panel must be removed (5 hex head screws). Tilted front of top up revealing broken injector. Retaining screw for injector accessible from behind control panel loosened and broken injector assembly removed. New (easily assembled--snap together) injector slid into holding slot on one side and screwed down with previously removed hex screw. Reassemble in reverse.

First removed the two lower screws from the front panel. I then unscrewed two screws holding the top(lid) of washing machine. I then lifted the lid and let it rest on its rear hinges. The syphon is removed by unscrewing four screws from the rear of the washer. I then cut the original clamp holding the syphon to the hose. New syphon was installed. Enclosed hose clamp was used to tighten around hose. Syphon was then then screwed back to the rear wall of the machine. Easy fix. Water leak solved.

It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.

Frist remover the two screws from washer front. The ones that are about 5 inches from the floor. Pulled front cover toward me and removed. The hose was right in the front that was cracked. It was held on by two hose clamps. I just removed the old and put in the new. No more water on the floor. Shipping was fast for the hose too. They said that if they recieved the order by 3pm it would be shipped the same day. I order at 3:01pm Sat. recieved Tuesday.

The instructions were clear. Did every step. Did 2 loads so far and everything works like new.

Since the washer is 28 years old, my first impulse was to rush out and buy a new one. However, I'm a DYI'er and I figured what do I have to loose by taking the front panel off (I had seen this done by the Maytag Repairman) and checking things out. After removing the two screws located near the bottom front of the panel, I pulled out on the bottom and the panel easily came off. I couldn't see any evidence of leaking water so I thought, "what would the Maytag Man do next". I figured "he'd run through a cycle to see if he could find the leak" so that's what I did. Sure enough, as soon as the spin and drain cycle came on, the source of the leak became apparent. There is a slight vibration during the spin which caused the hose to fail.

I then got on my computer, Googles "repair parts for Maytag Washer" and found Parts Select.Com. I was surprised (to say the least) to find the part I needed in stock. I place my order on Sunday morning and the part was delivered the following Wednesday afternoon. I installed the hose and replaced the front panel and was washing a load of jeans within 20 minutes.

I appreciate the service provided by Parts Select and will be ordering again when the need arises.

Tom Nelson
Fort Worth, TX

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

I used two vise grip wrenches in place of specialized tool that is no longer available. I put the vice grip wrenches on the brake assembly and hit them alternately with a hammer. I also used penetrating oil.

Note, the parts package stated made in USA but the bearings had China stamped on them.

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Make sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

opened front of washer, removed motor, replaced glides and springs, installed motor and replaced belts. Installed new hoses and vacuum breaker. Its been a week now and no leaks or other problems.