LAT9316ABE Maytag Washer - Instructions

It was fairly easy, start out by using a screwdriver and push down and out on the front cover and remove it. Take out the 2 small bolts that hold the top cover down to the sides and lift the top cover up and lean it back out of your way. On the bottom side of the agitator there is a small bolt that holds it down, loosen that bolt and pull the agitator out. The hardest part of the entire jod was to use a small chisel and hammer to take off the nut that holds the assembly down.Remember it has reverse threads,you have to use a chisel to back it off and use some WD40 to help remove the calsium build up that is around it. Once you get that large nut off, there is a set screw on the side of the assembly that you have to loosen up before you can take it off, it's a "star driver" head and not a allen wrench set screw.Just take your time and look at your new part and compare it with the old one and take your time and remember how you take the old part off,and you will not have any problem putting the new one on. This was the first time I ever worked on a washing machine, and by checking out the parts first and comparing everything,even someone that might not have much mechanical skills can change this out. My washer works fine and not a drop of water leaks anymore.One thing I did learn, if you change this part out and put it back together and try it out and it makes a funny sound and you smell something like its burning, you might did what I did. I thought I had it to tight, but I put the large nut on before I put the tub back on!!! The agitator was holding the tub down, but it could not spin in spin cycle.... Good luck with you repairs, you can do it.

Hardest part was figuring out how to access the internals (not through the back or the top) It turns out there are two screws on the lower front of the machine, not easily found, which when removed allow the front panel of the machine to swing to front and out of the way allowing full access to the internals from the front. The water was comming from one of two water pump hoses. The hose was held in place with 1" hose clamps and was easily changed out.

I removed the old lid switch assembly from washer and one by one exchanged the wires to replace correctly on the new part. I placed the new lid switch assembly in the washer using the screw to tighten the part in place. I turned on the washer and after the water level stop the wash cycle began immediately. Friends were impressed I used your web site to determine the part selection by the previous reviews and that I replaced the part with ease. Thank you for an user friendly web site.

Granville County/North Carolina
6/13/2010

Opened top - removed old switch assembly. Plugged in new switch and re-assembled. Had to reopen top when washer filled and did not start cycle. Switch assembly needed moved slightly in order to engage second switch.

it took a little longer to fix the lid switch becasue the you have to figure out how to install the switch after you takethe old one out. The old one popped out but the new one needs some twisting and pressure. It also is an ackward position to work in on the back of the washer front the front. I think the instructions could have been much better by warning the installer to pay attention when you take the old one out. But it worked and we fixed the problem for $22 and four days of waiting for the part.

Remove front panel. Then remove top of washer, two bolts at front of top. Then remove two bolts that hold switch assembly to top on right side of top. Switch gets pried out. It just sits in with small pins holding it in place. Wire connectors hold very tight. Install is reverse.

Unhooked H and C water lines. Removed cover plate with control valves. Pulled power wires off solenoid valves. Remove exit water hose clamp then hose. Put new valves on in reverse process. Checked washer through cycle to see it worked all OK. Had to make new mount ro install valves.

I opened up the control panel on the back by removing the 4 screws and then used the print that was inside to check where the power went from the power cord. I checked the power at diferent places and determined that I did not have power coming from the lid switch with the door up or down. You could here the switch click when you opened and closed the door but aperantly it was not working. After going on your web site and looking at the other posts I realixed that there was a fuse link in the switch that was probably blown. I ordered the switch and it was a simple matter to replace when it arrived. The washer works great once more.

I did a continuity check on the lid switch assembly since it was a) the easist to get to, and b) my wife's descreiption of how rthe washer stopped made me think it had something to do with the lid switch.
I found that all of the contacts were open regardless of the position of the switch, and I also discovered that there was a fuse inside the swithch. I decided to order a replacement part based on the presence of the fuse.
Upon repacling the fuse (a snap in affair), the washer was working again... my wife was impressed and I was happy!

Unscrew the hoses. Remove access panel. Unclip the 4 electrical wires. Undo the hose clamp on the top of valve and remove hose. Unscrew the one screw holding the valve in place. Remove valve. Reverse for installation.

Removed knob from switch,removed cover,pulled three connectors off,removed hose and unscrewed switch with a phillips screwdriver.

All I had to do is tilt the machine to expose the bottom and replace the belts. It was fast, easy and the machine works fine now.

I followed Dan from Mason OHIO instructions.They were perfect. I have a different series washer so I did not need the washer and retaining ring. I used 2 lengths of 4x4 to support the tub when smacking the bearing with the narrow side of a 2x4 to drive it out. You hit it from the inside of the tub. When installing the new one, use the wide side of the 2x4 to drive it flush.

It should have been extremely easy, but it was a little difficult because my laundry room is very small and I had extremely limited space to work in and also had limited lighting. However, after taking many minutes to strategically plan how to maneuver in the tiny space, I was able to loosen the giant clamp on the hose inside the washer and attach the new hose! It worked like a charm! My 25 year old Maytag is working again! The part came in a bag certified as a genuine Whirlpool part and looked exactly like the old one! No complaints! The online installation videos are wonderful!

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.