SAV4655EWQ Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randall from Shelbyville, IN
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pump was leaking and slotted end of drive was split
removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Gibbon, MN
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The discharge pump wasleaking
I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Gary, SD
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
water leaking when washing
I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Augusta, WV
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
belt wore out
replaced belt that was wore out. decided to replace pump while I had washer apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Boulder, CO
- Parts Used:
- WP40053901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Washing machine was leaking
Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wild Rose, WI
- Parts Used:
- WP27001113
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
waher would not advance in cycle
removed the timer & replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from New Lenox, IL
- Parts Used:
- WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
drain hose had water leak
remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SANDY HOOK, CT
- Parts Used:
- WP22002960
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
Bad tube seals and bearings
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Belleville, WI
- Parts Used:
- W10116791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Spin cycle became very loud
The instructions included were very good. The biggest problem I ran into was removing the inner tub from off the hub. Using PB Blaster was the trick there, but still took some effort to finally pry it lose without damage. The hub screwed right off after and removing the Triple Lip Seal was easy enough with screw drivers. Cleaned things up and replaced it by gently tapping around it to seat it evenly. Reassembly also went well, but I DO HAVE a story. Being as careful as I thought I could be, I still somehow broke the outer tub. I read about others experience, buying and using JB Weld WaterWeld to fix it. Now the washer is so quiet again that you have to look into the drain tub to see if it is spinning. AWESOME
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Martinsville, VA
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
wwater pump was leaking
My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from Tomah, WI
- Parts Used:
- 40061401, WP40045001, WP27001006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
wouldnt spin properly
removed motor removed belt replaced belt,spring,idler wheel, slid back motor in 4 bolts,plug in motor, run good on test run
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from northeast, MD
- Parts Used:
- WP27001006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Not spinning
I opened the bottom and found the belt had broke in half. i ordered a new belt from Maytag online and found a you tube video that showed exactle how to change it. the only thing i had to do afterwards was tighten the tensioner.eazy pezy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Saverio from Lake Worth, FL
- Parts Used:
- W10116791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
water leaking and noisey
Fixed the problem easy to do just take your time putting in bearing in plastic tub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Cornville, AZ
- Parts Used:
- 205217P
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
pump seal leaking
After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Deatsville, AL
- Parts Used:
- 40058501, WP40053901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer leaking water during drain cycle
Laid washer back on a appliance dolly, removed the front cover, checked to see if the hose was touching the motor mount (it was). Removed the drain hose from the pump and standoffs, removed the hose and disk from the back of the washer that holds the hose. Replaced the hose on the pump, turn the standoff to move the hose farther from the motor mount, and install it in the disk. May be easier to measure the hose and do the disk first as it is not easy to get the hose bent when it is installed first on the pump.
Was this instruction helpful to you?
Thank you for voting!