MAV7600AGW Maytag Washer - Instructions

Used a simple screw driver to push in the lid part...sooooooo simple!!!!!

All I had to do was take off the white cap on top of the spinner, place the dispenser cup in the hole and it was done! It works great even though there was no indication that my model would work with a dispenser. It was the best $3.95 I ever took a chance on!

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .

Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas

I followed Gary from Sioux City IA instructions. Very well explained.

Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.

Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.

I pried up the fabric sotener cover on top of the spindle with a screwdriver and removed it and softner cup holder-it twisted off. I then replaced entire softener unit which I had ordered.

Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws from snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!

The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pump assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.