MAV7258AWQ Maytag Washer - Instructions

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Pop the cap off the agitator/auger no tools needed. Once removed select a socket and a socket exstension. remove the screw amd pull off the part. Make sure to save the washer that may be still attached to the inside of the agitator. install the new agitator using the existing screw and washer. Takes about 15 minutes.

Removed 5 screws on back of the control tower.

removed the temperature control board and replaced with new board.

Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very greatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses and replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to the washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.

I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.

It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was stiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00

Followed the great instructions on your video