LAT9304AAE Maytag Washer - Instructions

Tried the water level control first. didn't fix it.
Then replaced the air tube for tub fill volume.

The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.

I thought it was going to be next to impossible to find a replacement part for an older washer. So my first attempt was to try to epoxy the original part, but the epoxy didn't hold up to the stress. I began thinking about what I might need to make a replacement part which was possible but not very practical. Although I dreaded trying to find this part online, I was very surprised and elated to happen upon PartSelect! Oh, by the way, this washer belongs to my daughter and I nave tossed the paper I wrote the model number on, so the model number was entered as the part number, sorry. At any rate, the the part was reasonable priced, and shipping about standard, but I still saved a lot by doing it myself rather than having a repair person for something this simple. Partselect online lookup made it easy to find the model and drawings to help me find the correct part nomenclature. AND, the part was in stock! So I am pleased with how this venture worked out.

Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Frist remover the two screws from washer front. The ones that are about 5 inches from the floor. Pulled front cover toward me and removed. The hose was right in the front that was cracked. It was held on by two hose clamps. I just removed the old and put in the new. No more water on the floor. Shipping was fast for the hose too. They said that if they recieved the order by 3pm it would be shipped the same day. I order at 3:01pm Sat. recieved Tuesday.

It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.

First, using a phillips head screwdriver, I removed the four screws on the top of the control panel and tilted it forward to access the timer. Next, I removed the button on the face of the control knob and removed the retaining clip. Next, I unscrewed the screws holding the timer on the control panel using a nutdriver. I then pulled the wire harness off of the broken timer and discarded it. I then plugged the wire harness into the new timer, placed the new timer back in place and secured it with the two screws. I then tilted the front panel back up into place and secured it with the four screws. Finally, I replaced the knob, retaining clip, and cover. The washer works like it is brand new! Gotta love a good ol' Maytag!!!!! It was easy and I'm a girl!

Since the washer is 28 years old, my first impulse was to rush out and buy a new one. However, I'm a DYI'er and I figured what do I have to loose by taking the front panel off (I had seen this done by the Maytag Repairman) and checking things out. After removing the two screws located near the bottom front of the panel, I pulled out on the bottom and the panel easily came off. I couldn't see any evidence of leaking water so I thought, "what would the Maytag Man do next". I figured "he'd run through a cycle to see if he could find the leak" so that's what I did. Sure enough, as soon as the spin and drain cycle came on, the source of the leak became apparent. There is a slight vibration during the spin which caused the hose to fail.

I then got on my computer, Googles "repair parts for Maytag Washer" and found Parts Select.Com. I was surprised (to say the least) to find the part I needed in stock. I place my order on Sunday morning and the part was delivered the following Wednesday afternoon. I installed the hose and replaced the front panel and was washing a load of jeans within 20 minutes.

I appreciate the service provided by Parts Select and will be ordering again when the need arises.

Tom Nelson
Fort Worth, TX

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Make sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

1.Unplug wash mashine.
2.Remove four sheat metal screws at top of control housing and seperate by pulling forward exposing timer.
3.Remove face plate with prongs holing it on pullout knob.
4.Remove clip securing pull out knob.
5.Remove pull out knob.
6. Remove spring.
7.Remove face plate with indicator line.
8.Remove two bolt with lock washers securing timer to metal housing.
9.Remove wire harness.
10.Reasemble in reverse.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

I turned the dial to other selections and nothing worked, no power. I checked the fuse box, but nothing was off, and then I checked to make sure electricity was working with a light bulb. I googled the situation and came across this site and read other posts as they sounded exactly like what I was experiencing. I ordered the complete lid assembly not just the fuse. The item arrived quickly in two days. After about an hour, as it was pretty easy to replace, the washer was working again! Thank you all for posting, as it saved me at least a couple hundred dollars.

Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!