LAT9606AGE Maytag Washer - Instructions

Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.

Took off the top rear off the washer, Removed the top control section,disconnected the wire harness, snaped out the old switch and installed the new one, connected the wire harness, put everything back together, and it was working again!

Switch material hardened due to old age & broke easily when force fitted. Ordered parts online & in two business day it arrived.

First open the lid & removed the side latch with screw driver carefully. Checked the length of the new plunger with the old one with respect to length & compare the stroke. Slide fit the switch & rectified the play in the plunger pusher with super glue.

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

Disconnected power. Then I removed the cover to the console on the back to gain access to the lid switch. Removed the switch assembly by hand and disconnected from electrical plug on machine. Attached new assembly unit to plug and reinserted new assembly onto machine. Reattached cover to console.

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!

I turned the dial to other selections and nothing worked, no power. I checked the fuse box, but nothing was off, and then I checked to make sure electricity was working with a light bulb. I googled the situation and came across this site and read other posts as they sounded exactly like what I was experiencing. I ordered the complete lid assembly not just the fuse. The item arrived quickly in two days. After about an hour, as it was pretty easy to replace, the washer was working again! Thank you all for posting, as it saved me at least a couple hundred dollars.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

The hardest part was actually finding the right part. It was easy to take of the control panel. make sure you unplug and plug in the correct wires....

I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.

That's about it.

Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

I followed the direction came with the part.

• I unplugged power electric wire from the wall.
• Unscrewed total of five screws from the back of the top console.
• Removed the top console to gain access the switch.
• I took pictures of the switch position for a future reference.
• Unplugged the switch wire by just pulling the plug.
• Carefully removed the switch and pulled the plunger out plunger assembly.
• Entered a new plunger in first and inserted a new switched carefully.
• Opened and close the lid few times to check the switch is going on an off properly. You will hear clicking sounds.
• Plugged the switch wire to the new switch.
• Reinstalled the console and screwed back the five screws.
• Plugged back the electric plug in wall outlet.
• Tested the washer by washing a full load of clothes.

The whole process took me about 30 minutes.

-Abhay