LAT2301AAE Maytag Washer - Instructions

My washer was sitting in a safety drain pan which made it difficult to work on due to the height of the pan walls. Managed to tilt it back and support on blocks well enough to access underside. Found two of the four leveling feet had fallen off, which was the ultimate cause of the problems from the cumulative effect of running unbalanced over time. Reinstalled these feet and had to remove rust to do so. I added two more nuts to the front feet to hold the adjustment tight. After adjusting to level, washer ran great and was no longer prone to unbalance. Procedure: Remove front panel- two lower screws and pry/pull off. Remove hoses at pump. Remove 3 mounting screws from pump. Remove belt from pump pulley. Push motor towards center of washer to release tension from other belt, and remove belt. Replace with new belt. Replaced old drain hose to pump and replaced all hose clamps with new. Install pump, replace pump belt. Level the washer. Replace front panel. Take the opportunity while the washer is open to clean out the dust from inside!

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

all went well until testing. tub level did not shut the water off, caused a spill

Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.

Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue

1. Remove front panel with phillips screw driver.

2. Remove hose from drum and exit pump

3. replace hose with new one (used some silicone grease on hose)

4. Tightened clamps with nut driver

5. ran a couple loads of wash to check for leaks

6. found none

7. replaced front panel - Job done

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor
Removed motor and slide
Cleaned and replaced slides and greased put back in washer secured
Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done
Great instructions that came with parts

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.

First I removed the two screws that held the front washer panel in place. Then I removed the two bolts that held the top on the washer. I then had to remove the four screws that held the top panel with the electrical parts in place in order to obtain access to the inside area where the screw was that held the fill injector was located. I next removed the screw that held the fill injector unit in place. I then pulled on the tab that held it in place and moved unit into a better place to replace the fill injector. I had previously cut the hose clamp during my investigation of the problem and replaced it with a pressure clamp. I then unscrewed the clamp, removed the bad fill injector and replaced with new fill injector. I then reversed the entire process to reassemble. The whole process turned out to be easier than I thought! The hardest part was diagnosing the problem in the first place.

I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.