MAT10DAABW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water tub leak, severe vibration while spining
all went well until testing. tub level did not shut the water off, caused a spill
Was this instruction helpful to you?
Thank you for voting!
During cycle, washer stopped and was smoking.
A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Allentown, PA
- Parts Used:
- 6-2095720, WP22001650
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Water leak at bottom of tub, leaking onto floor.
Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cumberland, MD
- Parts Used:
- WP22001187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water was overflowing inside the washer and coming out bottom.
First I removed the two screws that held the front washer panel in place. Then I removed the two bolts that held the top on the washer. I then had to remove the four screws that held the top panel with the electrical parts in place in order to obtain access to the inside area where the screw was that held the fill injector was located. I next removed the screw that held the fill injector unit in place. I then pulled on the tab that held it in place and moved unit into a better place to replace the fill injector. I had previously cut the hose clamp during my investigation of the problem and replaced it with a pressure clamp. I then unscrewed the clamp, removed the bad fill injector and replaced with new fill injector. I then reversed the entire process to reassemble. The whole process turned out to be easier than I thought! The hardest part was diagnosing the problem in the first place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Brambleton, VA
- Parts Used:
- WP213720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Small spring in the lid switch broke
I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from CROSSETT, AR
- Parts Used:
- WP22001083, 205353
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
timer inop
r&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Chalfont, PA
- Parts Used:
- WP6-2022030, 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer was not draining completely & at times a small amount of water would leak from under the washer.
Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Homer from HARVEST, AL
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
belt started smelling like something was burning
watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from MOUNTAIN BRK, AL
- Parts Used:
- WP212716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer is 27 years old. The washer lid bumpers were just worn out with age. It has been in constant use all these years raising 4 children with no other service or repairs. It has a matching dryer with the same track record. What a testament!
Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caitlin from ALBANY, NY
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Washer drum stopped spinning; Very loud squealing with burning rubber smell
We were not sure if the problem was the belts since they were not completely broken or overly worn down, but decided to try to put new ones on given the burning rubber smell and some light smoke coming from beneath the washer when it was on the spin cycle and the drum would not spin. We found some how to videos online and through the part select customer experiences, we ordered the belts and got them within 2 days. We put the new belts on, which is fairly easy and quick to do with the proper tools once you get the front panel of the washer off. The new belts seemed to have done the trick, as the washer began spinning again with no odd sounds or smells once the new belts were installed, and it has been running great so far. I highly recommend ordering from this site, as the parts are the real factory parts and are easy to find an order based on your appliance model. I found the pricing and convenience, as well as knowing the parts would be right and the best quality, to be the best part of this site, as ordering from other online retailers may land you with the wrong parts or kits with parts you don't necessarily need.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from CUMMING, GA
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I had a Burning Rubber smell, along with water leaking from the bottom of machine.
I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from NOVI, MI
- Parts Used:
- 12112425
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Squeaky belt noise when running washer + rubber burning smell.
Tilt washer. Remove old belts. Put in new. Tighten transmission bet and pump belt per YouTube. It works like new now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from HOMESTEAD, FL
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Worn belts
Slipped on belts no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland from Hudson, NY
- Parts Used:
- 6-2095720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator in washer wobbles
Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)
First time I had a problem with it. Sometimes just look for the simple things !
Part select refunded me for my part that I ordered very fast.
Great Company to deal with!
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)
First time I had a problem with it. Sometimes just look for the simple things !
Part select refunded me for my part that I ordered very fast.
Great Company to deal with!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Evansville, WI
- Parts Used:
- WP22001187, WP22001186
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Fill Injector Broke - A mouse may have contributed
I opend up the housing, found the broken part, ordered it, installed it, and had the washer working within 4 days of the initial break down.
Saved a lot of money over a service call, as well as time, and trips to the laundramat.
Saved a lot of money over a service call, as well as time, and trips to the laundramat.
Was this instruction helpful to you?
Thank you for voting!