WF316LAS Maytag Washer - Instructions

so simple could not beleive .

First I removed the retainer ring and then pulled back enough of the boot to get the door switch out and plugged in the new switch put the retainer ring back on and it was finished. With out the repair book I would have been lost on how to do the job.

Took off bottom panel by removing 3 torx screws. Opened up door seal, removed three latch retaining screws, unplugged three wiring harnesses. Installed new latch and reinstalled in reverse order.

Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.

1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

We watched the instructional video and it was a complete success!

Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

I removed the spring that goes around the rubber on front of drum, pulled back rubber near the lever, removed the 3 screws holding in the latch, reached in and disconnected the 3 plugs to part, connected new part put it in place screwed it in, put the part of rubber i pulled back, put spring back around the rubber, plugged machine in done

Replaced door lever (PS11741552) and door lock latch (PS11745016).

Initially I tried to replaced just the obviously broken (split) door lever, but then door would not close at all. Lever is as simple as it gets, so the problem was apparently the door lock latch.

After watching video (on this site) that shows it was fairly easy to access and install a new door lock latch (2 screws in back, 8 screws in front), I ordered a new door lock latch.

Took about 35 minutes to install new lever and latch.

Works perfectly now. I hope to get a few more years out of this machine.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

I am super excited that partselect.com asked me to do this review.

1-Order part on website, validate that everything is correct. It was. PS11741552
2-Part received is going to be a small box of screws instead of your vastly overpriced plastic door latch. This will happen your first time ordering, it is normal.
3-Item refunded through customer service and a new item sent out.
4-At this point you will need to do laundry, my recommendation here is to put you back against the door, maybe read a book and have a drink for the half hour it takes for a cycle. Nobody with a washer wants to hang out with the unwashed masses at the laundromat.
5-Receive another box of screws. It this point you will now believe that the screws are a metaphor for how partselect feels about customer service.
6-Contact customer service again, get another refund. At this point partselect will just give up and tell you to order the parts from the manufacturer. Once again by the picture on the site and the confirmation, you have order the correct part.
7-Total time here is over a week to 2 because the parts move slowly.
8-Order part on literally any other site.
9-When you get it unscrew the 2 screws from the broken part. Replace with the new part and screw the 2 screws back on.
Fixed!!

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.

My husband simply removed the old sensor and put the new one in. It was not difficult.