PAV1200AWW Maytag Washer - Instructions

No need for the Maytag repairman anymore. Video supplied was all that was needed. Could not have been easier.

The hardest thing about the repair was moving the washer out in order to repair it. All I did was remove the top back pannel behind the timmer . Threr was a total of 6 screws to remove pannel. Then 1 screw to remove timer from mount and unplug old timer. Then I pluged in new one, then put all the screws back in reverse order thats all !!!!!!!!

unscrewed screw holding old actuater in and replaced it whith the new part.

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

Removed the screws on the back plate pulled the hose clamps off removed the belt and three screws off the pump went back just as easy and the machine was like new again. If only all repairs was this easy!

Pretty simple repair--popped the fabric softener cup off of the agitator top and took out the bolt that secures it to the assembly. Removed the broken agitator top, replaced with the new one and reinstalled the bolt and softener cup. EZ as pie for only $24 including shipping! Great price!

Fabulous turnaround time from www.partselect.com. I had the problem corrected inside of 4 days using standard shipping. I will definitely do business with them again!

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

I checked the belt 1st. It didn't look like it could be the problem, but it needs replacement anyway. Replacing belt is very easy, this 1 is at the bottom of the washer.

1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped around 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.

There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.

Removed one bolt, main thing was I had to buy a 10 inch extension for the socket and wrench to reach inside of the agitator, pulled the old one off replaced the new one tighten the bolt and I was done. 10 minutes start to finish.

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

I followed the video you have on web site. Very good and easy to follow.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

Removing and installing the pump is theoretically easy, as everyone on this site has said so far. Just remove three hex-shaped screws, loosen drive belt and remove pump, then install new one using the same steps in reverse order. The trick is getting the screws off and on--they do not have slots for a screwdriver and there is not room around them for a socket wrench or pliers. I probable spent over an hour just on removing/replacing these screws and have many bruises to show for it. I ended up attaching a vice grips on the tips of the screws underneath the washing machine and screwing them out that way. And replacing the drive belt was horrifically difficult--that's where the other hour went. The devil was definitely in the details! If anyone had told me what I would have to go through to make this repair, I would have called a repairman. And I am an extremely handy person--I do stuff like repairs all the time, so it is unusual for me to say this. The good news is that the new pump works and the washer is back in commission.

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.