SAV505DAWQ Maytag Washer - Instructions

After totally disassembling the washer ; the parts arrived, wrong parts! called and resolved issue, recvd parts and proceeded without special tools, PB Blaster solvent is awesome!!! I removed the seal & bearing with little effort with a hammer and screw driver. Greased new seal and installed effortless. Waher back in operation in less than 2 hours of receiving the parts.

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Followed video on PartsSelect website, they made it real easy.

All I had to do was take off the white cap on top of the spinner, place the dispenser cup in the hole and it was done! It works great even though there was no indication that my model would work with a dispenser. It was the best $3.95 I ever took a chance on!

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

I pried up the fabric sotener cover on top of the spindle with a screwdriver and removed it and softner cup holder-it twisted off. I then replaced entire softener unit which I had ordered.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

We noticed that water was on the ground of the laundry room. We initially thought that the washer was leaking. Realized that the washer was going on the spin cycle without draining the water which caused the water the slosh over the edges and then leak on the floor. Well, I had to remove all the wet clothes and suck the water out with a shop vaccuum-this actually took most of the time. After taking the front of the washer off, we noticed the water pump was stripped out. After removing the pump, we then noticed one of our kid's socks jammed in the pump. How the sock got there is still a mistery. We found the replacement part on PartSelect and ordering was easy and fast. Thanks. We're washing clothes again.

I was able to remove the belt because it was worn through. However, I was unable to remove the pump as described in the instructions because I was unable to get my torq wrench to the bolts. I ended up having a repairman come in.

Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.

I seemed to have a more difficult time changing the pump out than others who had left their instructions on line prior to me.
What I has to do is remove the 4 bolts that secured the motor & mount to the frame. I then unplugged the wire harness from the motor leads.
I removed the belt tensioning spring & removed the belt.
I then removed the motor, motor mount and pump assembly. Turned it upside down & removed the pump. When installing the new pump you will need to remember how the belt was routed. A local parts house actually gave me a xeroxed schematic that showed me how to route it. A real life saver.
After that I turned the assembly right side up, bolted the mount into place, installed the new belt onto the large flywheel, attached the belt tension spring, plugged in the wiring harness and ran a rinse cycle. No leaks. Good as new.
Yes. It took a little longer than expected. But it was alot cheaper than having a service man do it.

Followed instructions that came with parts. Still making a noise not as loud as before, must be transmission bearing.

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.