Models > MAH2400AWW

MAH2400AWW Maytag Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for MAH2400AWW

Viewing 5 of 5

Manuals & Guides for MAH2400AWW

Click to download
Keep searches simple, eg. "belt" or "pump".
$11.77
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
Sold individually.
No Longer Available
$5.41
Sold individually.
In Stock
This is the front piece of the door to the appliance.
In Stock
$164.99
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
$11.09
Sold individually.
In Stock
This water inlet valve assembly is for washers. Water inlet valve assembly controls the water flow into the washer. The assembly may include multiple parts; refer to your parts diagram for a comple...
In Stock
This part is the replacement hot water valve for your washer. It is approximately 2-1/2 inches by 3-1/2 inches, and the valve head is approximately 1 inch in diameter. The hot water inlet valve in yo...
In Stock
On Order
No Longer Available
In Stock
Also known as door boot seal or bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for MAH2400AWW

Viewing 3 of 3
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Sarah from Kirkland, WA
Parts Used:
WP34001098
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Washer wouldn't spin / drain
First I looked up the error codes in the washing machine technical information pamphlet I got when buying the machine to determine what the problem was. It indicated that the machine wouldn't spin. After doing a few more tests I couldn't find the error code that was displaying, but the machine wouldn't run at all and just did a terrible growling sound. I tilted the machine back to get access to the bottom. Undid the flimsy corregated covering held in by 4 screws. In the right front corner I found the pump. There were 2 tubs connected to the pump; I undid each (a simple squeeze off holder) and found nothing blocking either passage. The type of pump is build as one part, so I was unable to open it up.
I decided to order a new pump assuming that was the problem and in fact it was. Replacing the pump was a piece of case. I undid the two tubes, disconnected the electrical connector then removed it from the washer casing with 4 screws. The new pump was easy to install -- screwed it in place with the 4 screws, reconnect the electrical part (just a simple female / male connection), reconnect the 2 tubs, put the bottom covering back on, and that was it. It's working just fine now.
53 of 60 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from Arlington, VA
Parts Used:
WP34001098
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Coin ruined drain pum impeller blade / SUDS error
Unplug machine, turn on its side (have bucket to drain water from hose), unscrew drain hose bracket on back (so you can fully empty water still inside machine) unscrew bottom plastic cover, locate pump on left, pull out electrical connector, unscrew hose clamps, twist off hoses, unscrew pump and replace, and follow the above steps in reve rse. I also made a coin trap from a sawed off plastic drain or downspout cover/protector and installed this inside the hose at the entry point to the pump, enlarging the holes enough to make sure they wouldn't easily clog with lint.
30 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from Fort Myers, FL
Parts Used:
WP34001179, WP34001178
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
I leaned on the door while open and it broke off!!
Removed hinge and all screws holding two halves together with glass between them put glass in new parts and replaced all screws hinge fits in there also
installed back on washer and away we went....
36 of 65 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!