LAT9356AAM Maytag Washer - Instructions

Made a 4 prong wrench from a 2" pipe coupling to remove retaining nut. Had to tap retaining washer a few times with hammer and after that it came off very easy. All other work was very easy. parts went together with ease. Saved company several $'s as we were told it was not recomended to repair and should replace washer. Under $100 for parts and a couple hours labor.

The job went fast an well

First, I secured one lid hinge ball in its appropriate position between the lid and the washer. While keeping the first ball in place I placed the other lid hinge ball as close to its intended position as I could get it. Next, I pushed the lid and ball into its position.

I took out the two screws in the bottom front panel of the washer, and rotated the front panel from the bottom away from the machine until the top or the panel was released from the machine frame. I then tilted the washer back to get access to the bottom of the machine. The pump pulley had split in half, and the bottom half fell off the drive motor shaft. The only problem I had was breaking free the set screw that holds the pulley to the drive motor shaft. I used a long arm Allen wrench and an adjustable "Cresent" wrench to apply enough force to break the set screw loose. Iclamped the upper transmission belts tightly to keep the motor shaft from turning while I loosened the set screw.

Replaced the 2 belts according to instructions received with the belts. Very easy repair

Found a very stretched, loose pump belt. Was able to pull it off pump pulley and motor pulley easily. Pushed motor assembly toward transmission pulley and removed wider drive belt. Wiped all pulleys clean. There's a double on the motor- one for drive belt, one for pump belt. Removed two hoses from pump using nutdriver. Removed pump. New pump installed. Installed two hoses on new pump. Installed drive new drive belt. Installed pump belt last. Slid pump to near farthest spot in slots. Tested for correct tension by pinching pump belt. Should be able to pinch center so two pump belt sides come within 1/4" of each other just as the spring tensioned motor mount starts to move. Pused washer back into place after external hoses connected. All new hose washers and filters on both hot and cold. Ran, checked for leaks - none! Absolutely perfect. Put front panel back on. No weird noises and drum empties perfectly every time. My wife is so pleased she's doing more loads.

old agitator stripped plastic splines.
pulled up and out old agitator, aligned and pushed (hard) down new agitator, tightened nut.
easy-squeezy!

Cleaned up a wet utility room floor!

Unplugged power cord to the machine and turned off hot and cold water at the stop valves.
Removed the top machine screw that holds the metal panel with the valve attached (on the rear of the machine where hoses attach), removed it from the machine with valve and hoses attached.
Disconnected both water hoses at the old valve, together with the 1/2" hose to the machine. Mark hot and cold positions.
Moved the electrical contacts one-by-one to the new valve.
Changed the old valve for the new valve (one screw attaches to plate).
Connected the inlet hoses and 1/2" hose to the new valve, making sure hot/cold on correct positions.
Replaced plate in the machine and secured with the machine screw.

*** NO MORE WADING SINCE REPAIR *****

I was told that it might be a clog in the tube.. we check the tubes that wasn't it Then I Google it and was told it might be the drain pump. I was just glad that Part Select had what I need because my machine is over 20 years old. We change the pump and now I hope I get at least another 20 years out of my machine. I will always use part select to get my parts. Thanks

Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.

A 5/16 socket on a ratchet was used to loosen a screw. Remove the agitator from the splined shaft by pulling straight up. Slide the new agitator onto the splined shaft and tighten the new supplied screw.

Make sure to release the springs and pulleys before you try to tackle the bolts that hold the motor base to the bottom of the washer. Mine were a bit rusty and took some force to break loose. Also it's a good idea to take pictures of how everything sits before you disassemble as the pictures in the repair kit are not very clear. Other than that it was pretty straight forward. Wiring was a breeze. . . . Good luck

Unfortunately, I couldn't find instructions for removing the top for exactly this model. First step was to remove the front panel by removing the two lower screws, grabbing the bottom of the panel, and lifting up until the clips on top of the panel let go. Next was removing from underneath the two screws towards the front that held the top of the washer on. This gives you easy access to the Fill Injector, but if working alone you'll need something to prop up the front of the top lid while you work on it. There is one screw that hold on the Fill Injector assembly (top and bottom). This screw is removed from the top, via the control panel. To get inside the control panel you need to remove the back of the control panel (very easy), just unscrew the 5 screws on the back of it. Then remove the one screw that holds the Fill Injector assembly in place. From under the front panel, use your pliers to remove the hose clamp and then remove the Fill Injector from the hose. ONE IMPORTANT ITEM, YOU'LL DEFINITELY NEED A REPLACEMENT HOSE CLAMP. The one you remove to take off the old, broken fill injector cannot be put back on. Put the new clamp loosely on the hose, then connect the hose to the new Fill Injector Assembly. Put the Fill Injector Assembly in place and use a piece of duct tape to hold it there. Then reinstall the screw that holds it in place from the top, inside the control panel. Reinstall everything in reverse, give it a test and then have a beer. You've just "given it to the man" and saved yourself $100+ on a repair bill.

Drum on the Maytag washer was not spinning is a true rotational pattern. Adjust or replace the centering springs.

How-to-description
I had to hack saw off the centering springs eye bolts since they were rusty and not adjustable. If you have to cut the old eye bolts as I had to, be careful... the spring will jump up an inch or two very quickly and you want to keep your hands clear. It makes a load noise and my wife asked "what happened". Not a big deal, just be aware of the spring returning to a normal state.
Place the new eye bolts in position and tighten the nut with 4 turns. With duck tape I held the eye bolts in place from under the machine. Had my son push the drum towards the replaced spring to shorten the length of the end of the spring to the eye bolt. Stretch the new springs with a long screw driver, one end against the washer body, and the other end near the handle. Pulled down on the scrw driver until the spring can hook onto the eye bolt. Before cutting the old eye bolts I measured the length of the eye bolt from the spring to the frame. Adjust the new eye bolts to the same length after the spring is stretch onto the eye bolt. Overall a simple project, cost $40 for me and the best advice is using the long screw driver to pull down on the springs.

I want to mention only the difficult parts.
The removal of the retaining ring/nut (which is under the agitator) . After 10 + years, it was very hard to move this part and it was eventually broke it to remove it. WD40 was used but not effective (to much calicum build up). You must turn the cone shaped piece (located under the inner tub) clock wise to get it to remove. A spanner wrench was not used to remove this. I used a punch and a tack hammer. We could not remove the old tub bearing (closest to the shaft), so we just cleaned it up with emory cloth and used the new tub seal/outer bearing. Spins great but have not been able to check the water leakage problem yet.
Caution: there are two dark colored ring (very thin) that go back on top of the rubber collar. These must be reused. These are hard to see. I pushed the old tub seal/bearing out with the end of a 2x4 (very slowly and carefully). I put the tub up on two of the 2x4's, for clearance off of the floor and used the third to knock the old bearing out. Old machine are very messy.