MAT10CSAGW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn from WILMINGTON, DE
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
1992 Clothes washer died mid-cycle
Replaced the lid switch assembly, works like a charm.
10 minute repair, 4 screws for the front panel, one for the switch assembly. Be careful not to break the plastic tabs that hold the right side of the assembly. As someone else noted, adjust the assembly front/back in the screw slot so the switch activates properly for open/close.
Fast shipping, great price, thanks Part Select!
10 minute repair, 4 screws for the front panel, one for the switch assembly. Be careful not to break the plastic tabs that hold the right side of the assembly. As someone else noted, adjust the assembly front/back in the screw slot so the switch activates properly for open/close.
Fast shipping, great price, thanks Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ms. Yvonne from OAKLAND, CA
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
After some troubleshooting I was pretty confident it was the Lid safety switch
Based upon my research on line and my 'hunch' I ordered the Lid Safety Switch for this old Maytag Washer. Got the part in good time and it was very well packaged. After having some difficulty in removing the one nut that held the old switch in place I installed the new switch, plugged it in and was delighted to hear the washer working like the old days. Now I have many, many loads of clothes to catch up on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Newton from DAPHNE, AL
- Parts Used:
- WP207166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Fills but won't turn on to wash
Removed the cover on top raised control panel at back of machine. Checked fuse, then lid switch which were okay. Checked Check-lid switch which was bad. Ordered and replaced. I always take pics with cell phone before removing anything to see position, wire colors, etc. Only difficult because of location on check-lid switch. Hard to reach even with right angle screwdriver. Had to bend some of the metal housing above the switch to get screwdriver in there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from IVOR, VA
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would fill with water but would not do anything else.
Done a troubleshooting problem online. Figured out the problem and ordered the part. Removed old part installed new part and I am a female not that it should make a difference but some would say it does. Had the old part out and new part put in and it took me about 30 minutes. Washer now works like a new machine. Very pleased and proud of myself. The part was the lid switch assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Santa Cruz, CA
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer fills with water but doesn't start
Changed lid switch. The hardest part was to remove the old switch. Wire connectors were very tight on the connection tabs of the old switch. Just out of curiosity, I did take the switch base plate apart just to see what the lid lever looked like underneath and how the adjustment worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Chalfont, PA
- Parts Used:
- WP6-2022030, 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer was not draining completely & at times a small amount of water would leak from under the washer.
Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from CROSSETT, AR
- Parts Used:
- WP22001083, 205353
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
timer inop
r&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from MOORESVILLE, IN
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer did not come on at all. Checked line fuse it was blown. Kept blowing so I suspected a bad kid switch. Yep. Replaced that and all good now
Followed above listed advice on replacing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from San Francisco, CA
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Cann't start
Hi there,
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.
Thanks,
Harry Lin
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.
Thanks,
Harry Lin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Richmond, VA
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water wouldn't run out of washer
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Homer from HARVEST, AL
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
belt started smelling like something was burning
watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from EAST SYRACUSE, NY
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
washer filled and stopped
I saw on internet that it was the lid switch and how to fix it. On this machine I have replaced timer and belts, machine is 22 years old.
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Roslyn Heights, NY
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would not start.
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from apple valley, MN
- Parts Used:
- WP207166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer just stopped within a wash cycle.
I called a local repair service and they wanted 95 bucks for the first 30 minuets. Any thing over that was an additional 45 bucks per half hour, plus parts. Since the washer was 19 years old I thought it would cost around 300 big ones to get it repaird. We could buy a new similar model for about 550 bucks so I said, what the heck. I'll invest the 18 bucks to see if this 80 year old can fix it. The repair instruction I read on your on line were perfect. FIXED IN ABOUT 20 MINUETS.Installed the lid switch, saved a bundle and maybe another 19 years on the washer. Thanks a bunch. Walt Apple Valley Mn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sid from Kearney, NE
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not start
Very easy, and simple. Replaced part that was sent. It was a simple process, open control panel, unplug machine. Unscrewed the old part, attached the new part and starting working right away. I am very impressed with this company and the speed they shipped the parts. Will continue to use if needed and tell everyone about this site.
Was this instruction helpful to you?
Thank you for voting!