LAT9806ABE Maytag Washer - Instructions

Following the lid switch installation instruction, it was real easy.

Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor
Removed motor and slide
Cleaned and replaced slides and greased put back in washer secured
Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done
Great instructions that came with parts

1. Remove front panel with phillips screw driver.

2. Remove hose from drum and exit pump

3. replace hose with new one (used some silicone grease on hose)

4. Tightened clamps with nut driver

5. ran a couple loads of wash to check for leaks

6. found none

7. replaced front panel - Job done

Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

I removed the front of the washer (two screws) and found the drain hose to be cracked near the top where it attached to the drum. A hardware store hose was inadequate because it crimped when bent in an S shape as required, so I ordered the proper part amd installed with two new clamps.
I bought a 5/15 socket driver to do up the clamps, and all is fine.

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

My washer was sitting in a safety drain pan which made it difficult to work on due to the height of the pan walls. Managed to tilt it back and support on blocks well enough to access underside. Found two of the four leveling feet had fallen off, which was the ultimate cause of the problems from the cumulative effect of running unbalanced over time. Reinstalled these feet and had to remove rust to do so. I added two more nuts to the front feet to hold the adjustment tight. After adjusting to level, washer ran great and was no longer prone to unbalance. Procedure: Remove front panel- two lower screws and pry/pull off. Remove hoses at pump. Remove 3 mounting screws from pump. Remove belt from pump pulley. Push motor towards center of washer to release tension from other belt, and remove belt. Replace with new belt. Replaced old drain hose to pump and replaced all hose clamps with new. Install pump, replace pump belt. Level the washer. Replace front panel. Take the opportunity while the washer is open to clean out the dust from inside!

all went well until testing. tub level did not shut the water off, caused a spill

removed the front panel on washer.
unscrewed the top and bottom hose clamps on the hose.
removed the damaged hose. put on new hose clamps on the new hose.
made sure the larger diameter end of the hose was on the bottom.
pushed the new hose into place on the tub water outlet and on the top of the pump.
adjusted the hose clamps into place and tightened them both.
replaced the front panel on the washer with two screws on the bottom of the panel in the left and right corners.

Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!