A202 Maytag Washer - Instructions

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

Could not complete because sent the wrong part (just a seal instead of the tube) several times, in spite of talking on the phone for hours. Eventually gave up and ordered from another company.

key to repair is to watch the video on mounting stem/tub seal as seen thru parts select. However, they use a nice new, clean,sanitized washer that may not reflect a 23 year old washer like mine. They give you the basics and it is invaluable to watch if you have never done this before. I strongly advise you buy a real spanner wrench made for your make. You may never need it again but it makes it much easier. Trying to use a punch or using a dremmel to operate on your large 'nuts' is, well, nuts! Get the wrench, just part of the cost of repair. See ebay. The first thing I noticed different between the video and my real life unit is the water hose connected to the washer, at the top of the tub cover. This did not exist in the video, but it is the way on my unit. So I did not disconnect it, just folded the top out of the way and tied it up. Then of course my real gripe with the video is that I have the old time band around the tub and the barrell, holding them together. They do not mate up very well and are not easy to put back together properly. In fact, installing the stem seals was easy and it fixed the original leak. I might add when you buy the replacement parts, you actually get 3 new parts. I suggest you use all the new parts in the package. You paid for them, you need them. Again the video only talks about replacing the very bottom seal, never mentioning the other parts they sold you in the bag. It is easy to figure out how to replace the other parts, they look like the ones you took off to get to the very bottom seal. Use all the new parts, regardless. So the only real issue is putting the band back on to hold the tub to the drum. We did not get it correct the first time and the unit would not spin, I had the top down too far. You could smell the rubber burning from the drive belt. They forgot to tell us about that!! Bums. So we loosened up the band, raised up the top piece and got it to spin. Of course, we did a large load, filled the water to the highest level allowed and when the unit hit the spin cycle, we got a leak from under the band. Thx video. To fix that we decided to never use the highest water level. So far so good. I can tell you the engineers failed on the design to mate up the cover to the tub. Other than that this can be done by us goobers, just take your time. And good luck. I must also thank my helper, neighbor John . for his added wisdom and support.

This washer was purchased in the early 1980s and is different from the one in the video and other repair instructions. You can recognize this earlier model by the agitator design. It only has the 4 paddles that start at the bottom and does not have the auger design on the upper part of the spindle as the newer ones do. While I was able to get the agitator to pop off by threading thin ropes under it and using a four-foot board as a lever, that was the end of my successful efforts. Even with the special tool and a five pound hammer, the lock nut would not budge -- even after overnight soaking in WD40. Yes, I did recognize the reverse threading. My next attempt would have been to heat the lock nut with a butane torch, but I gave up at this point and purchased a new washing machine on my way to pick up the torch. Would be curious to know if anyone else has had success with this older model as I saw other differences in the design that suggested that it may not have been compatible with this kit.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Install belts.

Viewed the very helpful video on your website, that spelled out all the steps to follow. The key point is to not forget the spanner nuts are left handed threads - even after noting that from the video, started the removal in the wrong direction, then caught my error and moved on through the disassembly process. In my case, I took time to deal with a lot of soap buildup cleanup in the outer tub, and even cleaned and put rust inhibiting paint on a few spots to try to get a little longer life out of the old machine. This repair cost far less than replacing it, and should get us several more years of service.

Removed 2 Philip screws from bottom front panel. The belts came as a set, so pay attention to the belt sizes when replacing them. Have had the new belts installed now for a week or longer with no issues. Looks like a good fix.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

Then found agitator shaft was rusted to spin shaft. Worked on that for awhile. Motor then burnt out. I quit and bought new machine. I had ordered a top end seal from you guys. I trashed the machine before your seal arrived. Called you. Nice lady said she would send an E mail so I could return unused seal. That message has not arrived yet.
Pat Wehling

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.