LAT9360AAE Maytag Washer - Instructions

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Washer originally purchased from Sears. Called Sears for repair. $65.00 to show up. Diagnosed the problem as a Bad belt and pump. Asked for approx. $250 to repair. I declined and ordered a belt and pump from PartSelect.com for half the cost. Took 10-15 minutes to install. Turned the washer on and put it through a drain cycle, it leaked all over the floor. Turns out the only problem was a cracked Outer Tub to Pump Hose. It took about 10 minutes to install. Whala, no leak. Now while I purchased an un-needed pump and belt from PartSelect.com, not their problem. Even though I purchased two items that were not required, the cost was still half of what Sears wanted to charge me for a repair that would not have fixed the problem. I will certainly continue to use and recommend PartSelect.com.

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

Easily

Removed the old hoses and screwed on the new hoses.

Had to look up how to pop the front panel off the washing machine - that was the hardest part. Once that was off, the top unbolted and the cover came off the back of the control panel with a few screws. Tilting the washer-top back, I was able to clip the new upper and lower injector (attached to each other in advance) to the washing machine. Then I realized that I needed to clamp the water line to the injector FIRST - so I found a small screw clamp and attached the water line. One screw and one plastic tab hold the injector in place. Everything went back together fine and worked great! Maytag washer keeps on truckin for another ten years!

I looked at the machine diagram on the website and removed the screw on the bottom and lifted up the from panel which allowed me to have easier access to the fill injector. Then I removed the back panel off of the control panel on the top of the machine and removed the screw that held the fill injector in place, attached the new fill injector using the hose clamp I ordered with the part ( you need a new hose clamp because the other one is useless after you remove the old injector). Tightend up the screw to hold the injector in place and replaced the back panel and front panel. It was an easy repair and only cost $28.00 with shipping. I easily saved $150.

Took off the upper back that had 6 screws with a screw driver. Found the lid switch . Removed it after I figured out how to remove it. It was a little tricky without instructions. Putting in the new switch was a little tricky also. You have to angle the front of the switch in, pop it in and then push it back so it can snap in. Once I put it in, the washer started right up. I was very happy. Instructions would have been very helpful. I am very pleased with this company because I received my switch in a couple of days. I will definitely use this company again.

Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!