MHWZ600TW00 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The hose from the detergent dispenser was dried out and cracked. Causing it to leak water during the different cycles.
I followed the video that accompanied the parts order confirmation. The replacement of the two parts, bellows and hose, were pretty straightforward. The job took a little less than an hour with little aggregation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CHESWICK, PA
- Parts Used:
- W11366227
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water leak
Removed top and front lower panels remove door panel.Remove ring from boot seal don’t damage seal.Replace hose,reassemble.Job is a lot easier if you purchase tool to re-install door ring seal.Tool is available from several sites on the net.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from ELLENSBURG, WA
- Parts Used:
- WPW10111435
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Leaking
Used suggestions on list - water to lubricate bellows and an extra hand to secure the bellows. Biggest challenge was seating the bellow that attaches to the rim of the outer tub. After getting the bellow lip seated the rest was fairly easy including the bellow seat that secures to the outer door assembly. Unfortunately, it doesn't appear that the bellow was the problem even though the symptoms - leaking under the door - was the same as noted on the list of problems. Had to order the dispenser-to-tub hose as that looks to be the problem (had to contort to follow the leak all the way up to the hose).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vito from CHICAGO, IL
- Parts Used:
- WPW10111435
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Washer bellow replacement due to intense mold
I followed the clear directions. Any hiccups were due to wear of the parts as they were quite old. This included both wire clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from OHATCHEE, AL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
pump impeller broken
Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from New Castle, DE
- Parts Used:
- W11366227, WPW10111435
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
When washing there was a water leak
I simply followed the video instructions which was presented very clear and the video shots was on point
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from S SAN FRAN, CA
- Parts Used:
- W11032829, WPW10111435, WP8540108
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Leaking
Followed the video except to use clamps to hold the Bellow To Front Panel Clamp in place while I worked the clamp around the from of the Bellow. I used a plastic pry tool in place of the suggested screw driver to pry the control panel off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- oscar from MEMPHIS, TN
- Parts Used:
- W11366249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
mice chewed thru hose
Pretty straight forward , It is a tight work are especially laying on your stomach. To make installation easier I recommend buying a 3-4 inch hose clamp instead of trying to use the old pinch style clamp. You will only need a zip tie if you reuse the existing clamps. remember to remove the plastic ball from the old rubber hose into the new hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BROOKFIELD, WI
- Parts Used:
- W11032829, WPW10111435, WP8540108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Water leaking from door
Much easier than I thought. Watched the video a few times.The front control panel gave me a little fight which the video edited that part out And the spring clamp reinstall took the most time.There must be a tool for that??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sag Harbor, NY
- Parts Used:
- W11366227, WPW10111435
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking from the bottom of the washer. Worse in the "clean washer cycle mode" which is a pretty violent cycle.
Watched the videos which were key! Thanks Parts Select! Replaced Bellows and dispenser hose. Cleaned all areas really well where new hose and bellows attached. Ran the washer in "clean washer mode" twice. Not a drop leaking. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from MORRISONVILLE, NY
- Parts Used:
- WPW10114608
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The drain hose had a leak
First unplug the washer and turn water off..Next take off back of the washer ( I used a socket set). Then underneath the front load tub, take that panel off to get to the pump (there are 3 screws in the front panel). Then get a towel put it underneath the water pump. Next take your pliers and squeeze the tab holding the end of the drain hose where it connects to the pump, Slide the clip up on the pump connection, pull off hose ,make sure your towel is underneath the end of the hose.Next reach your hand through the back of the washer and squeeze the plastic holder w[th your hand to release the hose. Then pull old hose out and replace it the the new hose. Just reverse the steps to put it in..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from DENISON, TX
- Parts Used:
- WPW10112972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drum baffle broke off
Ordered a new one. It was here on the second day. Lined it up, gave it a slight hit to snap it in place and I was ready to go. Didn't even miss a laundry day. I'm 70 years old and I had no problem doing the repair.
Was this instruction helpful to you?
Thank you for voting!
Latch broke
Boyfriend followed directions and YouTube and I’m sooooo grateful!! My door shuts easily.. I love my machine and my man with your directives and your parts made my magic happen!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from housatonic, MA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
wouldnt pump water out
raised front of machine about 6 inchs bigest pain is getting water out after that its easy.open drain just a bit other wise it will pour out all over about 4 pots worth if its full
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ABILENE, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer would not drain
Checked for 120 V AC at pump connector. It was present . Pump was hot. Ordered new pump. Changing the pump is a piece of cake. Just tilt machine back and rest on a brick. Remove 3 5/16th screws . Disconnect 2 hoses and 1 plug. Took 10 minutes tops. Back in business.
Was this instruction helpful to you?
Thank you for voting!