MAV7600AWQ Maytag Washer - Instructions

First tip front of washer up about six inches and block. Removed belt by holding the old belt to the side of the big pulley and turn big pulley on opposite side with the other hand. Old belt was dirty, black and some carbon on floor. Cleaned up. Put belt around motor pulley and water pump pulley. Hold belt in track of big pulley. Turn big pulley with opposite hand until belt goes around the big pulley. The motor has a spring that maintains the tension.

Wife thinks everything is back to normal. Get a cool drink out of refrigerator while she carries on and thinks you are a hero.

Special note: Be sure water is out of washing machine. There are instructions on the internet but I have owned Maytags for over forty years and know belt replacements are occassionally replaced.

I thought I was going to need to replace the leaking washer machine. Water was every where and after checking the main sewer drain was ok I lifted the washer and found the water pouring out the bottom when i put it on.
After finding out how to get the whole top open and the front panel off I was able to locate the source of the water leak on my washer machine. The cause was split in the plastic hose that goes from the tub to the pump. After the new hose arived I was able to replace it within 10 minutes. So far so good. Thank you Part Select.

I unplugged the electric power cord and disconnected the two water hoses and the drain line from the wall. It was messy as water leaked from the disconnected hoses. I tilted the washer forward and leaned it against a bench for support. This exposed the bottom of the washer from the back. I removed the v-belt from the three pulleys. The motor mount was spring loaded making it easy to remove the v-belt from this pulley first. After removing the v-belt, I then removed the 4 screws to the small plate on the back of the washer to gain access to the water pump. I then removed the two water hoses from the water pump using vice grips to squeeze the clamps and slide them off of the hoses toward the water pump. After removing the two hoses (a little messy again), I removed the water pump by using a socket ratchet to loosen the four bolts. I replaced the water pump with the new pump and then reassembled everything in reverse order.

I found your site and looked at possible "symptoms" of the problem. Went to my washer propped it up with a 2 x 4 and manually spun the belt and sure enough the pulley on the drain pup was shot and grinding metal on metal. Ordered the new pump with pulley and a new belt (might as well change it when I had the thing in pieces).

1) Opened the front of the machine and then propped up the machine.

2) Placed a pan underneath to catch the water that remained in the pump when I disconnected the two hoses attached to it.

3) Removed old pump with socket wrench

4) Replaced with new pump purchsed from you all.

5) Reconnected the two hoses.

6) Installed new belt.

7) Closed up machine and BAMM! works like it was brand new!

You all Rock! Cost of parts and 20 or so minutes of my time is a lot less than calling a repairman or replacing the machine!

Thanks for the help!!!

This was easy except for the e-ring which was extremely difficult to remove. When I put the new one on I filed down the bottom of the front edges to make it easier to slide it on. Beware: If you have the washer tipped back against the wall when you do get the e-ring off everything will come sliding off the shaft all at once and go everywhere. These parts are covered with black grease and made quite a mess so you might want to have someone hold them in place so you can gently slide them off one piece at a time.

I took out all the tubs and the apparatus holding the gear and thrust bearing assembly. I used a homemade tool (long zipties) to pull the springs off and to put them back on. After that I just replaced the thrust bearing with the new kit and put everything back together.

I tipped the washing machine back to allow me access to the bottom of the washing machine to remove the belt from the water pump. After removing the belt, I righted the machine, unscrewed the three screws holding the rear access panel on. I used pliers to remove the clamps from the inlet and outlet hoses then removed the hoses. I removed three screws holding the water pump on to the bottom panel of the washing machine. I removed the pump and replaced it with the new pump. I then reinstalled the screws, the hoses, the clamps, the access panel, and the belt. I plugged the washer back in and - viola! It works again.

First I tipped the washing machine onto its front. I removed the belt on the bottom of the machine. Then I removed the screws that held the cover in place on the back of the machine. Next I removed the two hoses that were connected to the vertical pump using pliers to pinch the clamps. I then removed three screws that held the vertical pump in place. I took the new verticle pump with pulley and mounted it to the washer and putting the washer machine back together using the previous steps in reverse order.

I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,

Removed front cabinet, removed 6 springs holding tub down, removed pump hose, removed drive belt from motor,lifted tub out the top and placed upside down, loosened all six hex bolts(did not loosen or remove drive pulley) backed all six bolts out and left 4 threads showing, slipped old snubber out cleaned all surfaces with alchohol and slid new snubber in. Put corn starch on base where snubber rides, lifted tub back in, hooked up all six tension springs with auto brake tool. Put belt back on. . . Done. . No more beating itself to death.

Overall, this repair should have been quite easy. The problem was removal of the old seal nut assembly. It was a bear to remove, and ultimately I had to surgically remove it from the washer in pieces. Unfortunately I broke the outer tub (plastic) in the process of getting the nut off. Once I had the silly plastic nut off, and the tub repaired the balance of the repair was absolutely easy.

My summary: This repair is really easy IF the plastic seal nut assembly comes off easily. If it doesn't budget easily, go ahead and chip it apart to get it off, being careful not to damage the threaded part of the agitator shaft. The new one will completely replace the chipped away nut.

Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orientation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.

I tilted machine onto the front to acces the rear panel. i removed the three screws to expose pump, took of the drive belt located under appliance, removed the three pump screws and removed old defective pump. I installed new pump, put the drive belt back on, reinstalled back panel and screws, hooked the appliance up and started. Been running great ever since. Entire process too about 10 min.

The washing machine would shake very loudly when spinning.
Found red oil under machine. Asked experts, they said "buy new machine, not worth repairing transmission".
replaced small oil seal and drilled small hole and added some transmission oil(auto) then sealed hole. replaced belt just because the other one was oil soaked.
Works great, Like new, cheap fix under $20..

Placed the washer on 2 brick under the front. Removed the belt, used a straight blade screw driver for the lifting of the top off. reoved 2 bolts off the face and removed the screws of the water pump. Water pump was messy with smelly water but a bowel and a towel helps. Placed the pump on, reversed the tear apart...placed the belt on the bottom. Removed the brick under the front. Hooked up the water supply...plugged in and did a load..it worked perfectly....Thanks!!!!