MAH14PDAAQ Maytag Washer - Instructions

Using online disassembly instructions removed and replaced front and rear bearings. Then attempted to install the seal kit that was purchased online from partselect. Com. Was supposed to receive both seals plus lubricant so that no matter which seal I needed I would be covered. The kit I received had 2 seals that were identical. . . I needed, as it turned out the early seal kit, but unfortuneatly I had 2 revised kits. Of course I tried to assemble one but it just won't work. The seal kit must be the correct one. I didn't give up. I ordered another seal kit online from appliance partspros. Com and received both kits as advertized. . . One being the early version plus a small packet of grease along with all the other required loose parts and was able to complete the repair. The second time around proved much easier because of the experience factor.

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.

removed the door &the top took the tightener off the bellow took old one out put new one on and clean all parts and put it back together works like a new one love it.

I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all

Replaced the belt and motor isolators. Watching your video made it very easy.

Watched the video, worked just like shown so as quick as you can take out 8 screws you can make the repair. Turned out it was the MCB but maybe this part (wax motor) Will save a main control board failure.

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

removed front panel. removed brakets holding top. lifted top hinged backward. Removed tension spring and cable that secures the seal to the drum. Pulled seal out. Put new seal back in. Secured with cable and spring. Reassembled top and front.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

Replaced wax motor. You must also replace R11 (3.9 Ohm carbon film resistor (1/4 watt), Q6 Triac (Mouser 526-NTE5656), replaced Jp 18 (jumper) with a fuse (Mouser 576-0251.500HAT1l. This job requires the use of a solder sucker in order to remove parts without lifting up cooper traces.I have had experience with many electronic projects,and could have done this one easier if I still had the proper tools.A solder sucker is cheap, and without it, you will damage the traces. I did, but used a continuity checker to verify I made solder contact with the traces. I have six of these stacked washer/dryers. All failed after about a year of use. I am in absolute disbelief regarding all the stories about how easy this repair is.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

Followed the video, besides the spring, everything was easy.

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!