LAT9806BGE Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from SANTA FE, NM
- Parts Used:
- WP213045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water was leaking on floor
1. Remove front panel with phillips screw driver.
2. Remove hose from drum and exit pump
3. replace hose with new one (used some silicone grease on hose)
4. Tightened clamps with nut driver
5. ran a couple loads of wash to check for leaks
6. found none
7. replaced front panel - Job done
2. Remove hose from drum and exit pump
3. replace hose with new one (used some silicone grease on hose)
4. Tightened clamps with nut driver
5. ran a couple loads of wash to check for leaks
6. found none
7. replaced front panel - Job done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ANNAPOLIS, MD
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
waterpump leaked where plastic housing upper and lower halves were bonded
new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from dracut, MA
- Parts Used:
- WP207166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
washer just stopped working
after checking obvious reasons (plugged in, breakers,) i took off control panel cover and saw that the fuse was blown, replaced it, plugged back in and it worked. After 1st wash was done, again it didnt work and the fuse was blown. I followed the wires from the fuse and they led to the lid check switch,which had a char mark leading me to beleive it was fried. I checked for continuity with an ohm meter(after disconnecting the power of course) and got no reading after pushing in the red button on the switch.I googled maytag replacement part and Partselect came up.Easy to understand ordering, and $20(including shipping,2 days later and about a half hour install, my machine was running
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Coldwater, MI
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Water leaking out of the bottom of washer
Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ZHIQIANG from Plainsboro, NJ
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
when turn on the machine, nothing happened
Following the lid switch installation instruction, it was real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Sun Valley, CA
- Parts Used:
- WP213045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
crack in the original hose just below the top hose clamp.
removed the front panel on washer.
unscrewed the top and bottom hose clamps on the hose.
removed the damaged hose. put on new hose clamps on the new hose.
made sure the larger diameter end of the hose was on the bottom.
pushed the new hose into place on the tub water outlet and on the top of the pump.
adjusted the hose clamps into place and tightened them both.
replaced the front panel on the washer with two screws on the bottom of the panel in the left and right corners.
unscrewed the top and bottom hose clamps on the hose.
removed the damaged hose. put on new hose clamps on the new hose.
made sure the larger diameter end of the hose was on the bottom.
pushed the new hose into place on the tub water outlet and on the top of the pump.
adjusted the hose clamps into place and tightened them both.
replaced the front panel on the washer with two screws on the bottom of the panel in the left and right corners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from AMORY, MS
- Parts Used:
- WP207166
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer filled with water, but would not start.
Removed front of control panel on the washer. Found the lid check switch, removed one screw, leaving the wires attached and replaced the old switch with a new one. Removed the wires from the old switch and place them on the new one. Reconnected the machine to the outlet,,closed the lid and listen to it run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from GROSSE PT PK, MI
- Parts Used:
- WP22001650, WP22001007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Tub gasket leaking because of age.
Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.
Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.
Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.
Was this instruction helpful to you?
Thank you for voting!
water tub leak, severe vibration while spining
all went well until testing. tub level did not shut the water off, caused a spill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Antlers, OK
- Parts Used:
- 6-2040130
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Leaking water at bottom of unit
Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Stevensville, MD
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Washer would stop spinning on its own
Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from MOORESVILLE, IN
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer did not come on at all. Checked line fuse it was blown. Kept blowing so I suspected a bad kid switch. Yep. Replaced that and all good now
Followed above listed advice on replacing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Allentown, PA
- Parts Used:
- 6-2095720, WP22001650
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Water leak at bottom of tub, leaking onto floor.
Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shannon from LIBERTY TWP, OH
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer quit working after partially filling with water
I found the mostly likely parts to fix my problem on the website... that washer would not start, stating the lid switch assembly fixed the problem 66% of the time. I used an ohmmeter to test the switch and could not find any continuity. Replacing the switch took less than 5 minutes. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sid from Kearney, NE
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not start
Very easy, and simple. Replaced part that was sent. It was a simple process, open control panel, unplug machine. Unscrewed the old part, attached the new part and starting working right away. I am very impressed with this company and the speed they shipped the parts. Will continue to use if needed and tell everyone about this site.
Was this instruction helpful to you?
Thank you for voting!