LAT9806AGE Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ZHIQIANG from Plainsboro, NJ
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
when turn on the machine, nothing happened
Following the lid switch installation instruction, it was real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RANDALL from ARLINGTON, TX
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Washer would not fill with water, either temp.
Checked the fuse it was blown. So I replaced it, pluged the washer back in. pull the start knob that's when the lids switch sparked and blew the fuse again.
Found you on line ordered the complete assemble to save me from the trouble of slowly change each.
Switch out the wiring from old to the new assemble. Line it up, one screw and a little adjusting and the Maytag is back in business!
Thxs Guy for the quick shipment had it in two day on a ground shipment!
Found you on line ordered the complete assemble to save me from the trouble of slowly change each.
Switch out the wiring from old to the new assemble. Line it up, one screw and a little adjusting and the Maytag is back in business!
Thxs Guy for the quick shipment had it in two day on a ground shipment!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from AMORY, MS
- Parts Used:
- WP207166
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer filled with water, but would not start.
Removed front of control panel on the washer. Found the lid check switch, removed one screw, leaving the wires attached and replaced the old switch with a new one. Removed the wires from the old switch and place them on the new one. Reconnected the machine to the outlet,,closed the lid and listen to it run.
Was this instruction helpful to you?
Thank you for voting!
water tub leak, severe vibration while spining
all went well until testing. tub level did not shut the water off, caused a spill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from GROSSE PT PK, MI
- Parts Used:
- WP22001650, WP22001007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Tub gasket leaking because of age.
Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.
Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.
Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Newton from DAPHNE, AL
- Parts Used:
- WP207166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Fills but won't turn on to wash
Removed the cover on top raised control panel at back of machine. Checked fuse, then lid switch which were okay. Checked Check-lid switch which was bad. Ordered and replaced. I always take pics with cell phone before removing anything to see position, wire colors, etc. Only difficult because of location on check-lid switch. Hard to reach even with right angle screwdriver. Had to bend some of the metal housing above the switch to get screwdriver in there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from EAST LANSING, MI
- Parts Used:
- WP22001682, WP211726
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer fills but would not drain. Pushing the lid switch in and out several times would actuate the switch.
Remove the rear panel covering the control panel. Remove the two screws on each side of the upper control panel. The top removes with gentle (or not so gentle) taps toward the front of the washer. Lift the upper away but be careful of the attached wires. Top must be removed or switch cannot be removed as it cannot pass the cycle selector. Note the wire positions and colors to the switch assembly, remove them, and loosen the screw holding the switch assembly in place. Tilit assembly up like opening a book and lift up and away from the washer being careful of the lid switch actuator below. Replace with new assembly, making sure actuator is positioned to activate switches, and reattach the same screw. Reattach wires to appropriate places, replace top control panel and reattach screws, replace rear panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ms. Yvonne from OAKLAND, CA
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
After some troubleshooting I was pretty confident it was the Lid safety switch
Based upon my research on line and my 'hunch' I ordered the Lid Safety Switch for this old Maytag Washer. Got the part in good time and it was very well packaged. After having some difficulty in removing the one nut that held the old switch in place I installed the new switch, plugged it in and was delighted to hear the washer working like the old days. Now I have many, many loads of clothes to catch up on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Antlers, OK
- Parts Used:
- 6-2040130
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Leaking water at bottom of unit
Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from MOORESVILLE, IN
- Parts Used:
- WP207166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer did not come on at all. Checked line fuse it was blown. Kept blowing so I suspected a bad kid switch. Yep. Replaced that and all good now
Followed above listed advice on replacing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shannon from LIBERTY TWP, OH
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer quit working after partially filling with water
I found the mostly likely parts to fix my problem on the website... that washer would not start, stating the lid switch assembly fixed the problem 66% of the time. I used an ohmmeter to test the switch and could not find any continuity. Replacing the switch took less than 5 minutes. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Allentown, PA
- Parts Used:
- 6-2095720, WP22001650
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Water leak at bottom of tub, leaking onto floor.
Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from EAST SYRACUSE, NY
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
washer filled and stopped
I saw on internet that it was the lid switch and how to fix it. On this machine I have replaced timer and belts, machine is 22 years old.
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from San Francisco, CA
- Parts Used:
- WP22001682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Cann't start
Hi there,
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.
Thanks,
Harry Lin
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.
Thanks,
Harry Lin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Richmond, VA
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water wouldn't run out of washer
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this instruction helpful to you?
Thank you for voting!