MAV8260AWQ Maytag Washer - Instructions

Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.

I removed the screws to loosen the belt, took off the old belt and put on the new belt. Tightened it up and has been working ever since.

Thank you, Lester

you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)

Diconnected water lines, layed washer on its side, spun pulleys and pulled belt off at the same time, put the belt on in the same way. VERY simple

Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

Parts look up was simple. part was priced right. part received in a timely manner and was as advertised. installation was quick and painless.

Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

I knew it was the belt because of all the noise it was making. I ordered the belt and it arrived real fast. I pulled the washer away from the wall and tipped it back at about a 45 degree angle against the wall so I could get under it. I propped it with a bucket. I then pulled the old belt off and spun the new one on. Real fast & easy.

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.

Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.

Easy repair replacing the water valve assembly. Good advise from other posts helped much.

First we stuck cardboard in the hole until the new plastic part came and then we snapped it into place. I feel like a rocket scientist...but I learned that you should not stand on your washing machine lid.

followed directions you gave. Simple

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

My Maytag Atlantis MAV7550AWW does not have a side inspection door like many have posted. After taking most of the washing machine apart I noticed in the front between the top lid and the main body there appeared what looked like some type of clips. I used a butter knife and pushed the V clip back and the one side of the top lid was released. After doing the other clip it was clear that was how to access the motor etc. After the top was open, it's hinged by a plastic hinge, you will need a small wrench and have to move the tub to the side to take off two small nuts also in the front. 8mm I think. Then the entire front of the machine comes off and the pump was right there. Time to remove and install the new pump was 15 minutes. I replaced the belt at this time also but had to lay the washer on it's side. Put the belt on two of the pulleys and pull hard. You will see that one of them is a spring held tightener. I did this outside on the deck as you will have water in the hoses and pump. After all was hooked up I ran a wash cycle only to hear that screeching sound was still there. My best guess is that it's a tub motor going. I am just going to use the washer till it dies then get a new one.