LAT9806DAM Maytag Washer - Instructions

I watched the video and everthing went pretty well. The only problem I had was removing the Clamp Nut. My Washer is more than 10yrs. old so there is a lot of water and lime build up. I use a Cole Chisel and a Ball Pen Hammer to break the Clamp Nut. Because you can dispose of it anyway a new Clamp Nut comes with your Mounting Stem/Tub Seal Kit. The Tub wrench comes in handy for removing the Mounting Stem and to reseat the Mounting Stem. You are also going to need the Tub Wrench for reseating the Clamp Nut. You can order a Tub Wrench online there are various web sites.

After unpluging cord and disconnecting hoses, I layed the washer over on its front. I simply rolled both belts off their pulleys and installed the new ones. This was easier than I thought! I gave a turn or two on both sets of pulleys to make sure something wasn't preventing the pulleys from rotating properly and all seemed to move okay. After reconnecting everything and doing a test run, I discovered that the transmission was not moving as it should and the belt was still binding. Turned out the 25+ year old transmission finally gave up! I doubt if any new washer I buy will last half that long

After watching the video on this website and testing the lid switch with my volt/ohm meter I figured out I had a bad lid switch. I ordered the part on Friday evening and got it on Monday. Took me 5 minutes to replace. My problem was solved. I can now add "washer repair man" to my resume. Just Kidding!

We took the back off the top where the controls are and loosened the top so we could have access to the part. It was easy to change out. The only goof we had was we didn't slide the part far enough forward the first time and the lid switch didn't engage. (fixed one problem, the washer filled but now it didn't run) As soon as we moved the switch assembly forward about a half an inch everything worked, my wife was smiling and able to wash clothes again!

I suspected the pump, so, once I removed it, it was obvious that the shaft from the pump pulley to the impeller was broken (the pulley turned, but the impeller was not turning).I ordered a genuine "Maytag" pump from Parts Select, even though it cost me twice as much as other pumps advertised on Amazon.com. Why fool around? While I was at it, I also ordered 2 new belts from Parts Select, even though the belts on the machine looked OK. But heck, the old belts were 26 years old! What a great machine this old Maytag! This is the first time in 26 years that it failed me...The only reason I looked at the Parts Select repair video was to know what tension to put on the pump belt...BTW, I ordered the parts on the weekend, and they were sitting on my front porch Tuesday, early morning. Impressive..

I tried to get an appointment with our local appliance repair company, but they cancelled and wouldn't reschedule at a convenient time, so I decided to do it myself. Determined that the Mounting Stem/Tub Seal kit was the needed part and ordered it here. Also had to order the specialty spanner wrench from another website. Parts were delivered in a timely manner. The online video was very helpful and the removal and replacement of the defective part went smoothly. The only problem with the actual repair was with removing the old tub seal gasket -- it took quite a bit of coaxing to get it free. The new parts went in with no problems. However, we have an older model than the one shown in the video -- it has the metal tub top cover with the rubber gasket and ring clamp. This cover is tricky to replace properly. It has to be at just the right height to avoid interference with the spinning inner tub (too low) or with the washer lid (too high). You also have to make sure that the rubber gasket it not twisted or crimped by the ring clamp. It took me three tries to get this just right. After that, everything worked fine and the leak is fixed.

I hastily (miss diagnosed) the symptoms by assuming that the Drain Pump was in fault, Ordered the Drain Pump part online on Sunday got it early on Wednesday. Installed the Drain Pump but the timer would not move. So back to drawing board. Got on the phone with the nice people on PartSelect ordered the Lid Switch Assembly. Got the part in less than 20 hours To install the Lid Switch assembly remove the back panel by removing 3 sheet metal screws at the top and 2 at the bottom now you will have access to all the wires and the Lid Switch Assembly. It is attached with one sheet metal screw. The hole in the Assembly is slotted so you may have to slide it back and forth for the switch to get activated when you open the door. Installed the part, plugged the washer machine in filled the tank. The washer machine came alive the timer was moving (the washer machine start working again). This washer machine should be good for another 20 years. By the way this was the first breakdown on this washer machine after 20 years of service. Thanks PartSelect for well trained people and prompt service I couldn't have done it with out your help.

Removed old hose and replaced with new one.

Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

Tried replacing timer, mixing valve, drain pump to no avail. Bought the lid switch assembly. That worked, here's how to do it. Unplug washer. Remove two philips head screws on top control panel to remove front. The lid switch assembly is mounted on the back behind the timer, and easily recognizable by the fuse. Remove wires (I needed wd40 for this part) from old assembly and connect to new assembly. Use nut driver to remove nut that holds the assembly to the washer, being careful to note exactly where the assembly was mounted, because it's adjustable. Bolt new assembly in place. Replace control panel cover (be sure that the bottom lip fits inside before replacing the screws on top. Plug in washer. Turn on washer. You're done.

Removed the old one installed the new one

Replaced the pump. The front panel screws were rusty. I also replaced the belts at the same time. The repair video told me just what to do. I wouldn't have known about the belt tension otherwise.

Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.