A208 Maytag Washer - Instructions

First I unplugged the power cord from the wall. Then I turned off the water supply shut-offs at the wall and removed the hot & cold connections at the rear of the washer. Then I removed the two screws that held the assembly in the rear of the washer. I then pulled the assembly out about 3-inches, marked the new assembly to show the proper color of wire for each lug and disconnected the four wires at the lugs. I disconnected the rubber fill hose from the assembly and removed the assembly. Next, I installed the new assembly in the reverse order. It worked fine without any leaks & saved me from buying a new washer. My old washer now gets my clothes cleaner than it has for years - much quieter and quicker too.

Pull washer out from wall. Remove front panel (2 Philips head screws), swing bottom of panel out, remove panel. Tilt washer backwards, lean against wall to expose area under washer. Roll off old belts, roll on new belts. Move washer back upright, replace front panel, replace the philips screws, move washer back to original position.

took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you

Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.

Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.

Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.

Could not repair. The gearbox on the agitator was broken and that kept the agitator from working. Do not assume it is a belt problem on a washer built in 1987.

Partselect.com gave me a very helpful list of parts per symptom. Said that there is an 88% chance that belts were my problem. Since the machine is 200 miles away I ordered two other parts as well. Belts fixed it! Took front cover off (not totally necessary). When the machine is tilted back belts are exposed underneath. Two belts later I was up and running. This site is really great.

I followed the instructions on this website to a T. You can take the front cover off and you will notice a small drip from the tub area where the Hub bearings (above the tranny) meets the washing tub. Once you've identified that the leak is indeed coming from that area and not a loose tube. Allow the washer to complete the job and drain the water. Then simply unplug washing machine before starting the process of the repair. It is very important to remember that you must have a spanner wrench before attempting to perform this repair. keywords=spanner+wrench came within two days with Prime Shipping. Also be sure to order the replacement parts from this site. It takes about 3 days to arrive however so be prepared to be without a washer for a few days. Other than that just follow the instructions provided and there is a very good step-by-step video on this site .

well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to order a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.

Removed the old hoses and screwed on the new hoses.

Once the front and top of the machine were opened,
I loosened the clamps on each end of the injector. I removed the rubber injector valve and the plastic injector nozzle was inside. I placed the new nozzle inside the rubber valve making sure the lip of the nozzle was locked in the rubber valve as on the one I had removed. I used a little detergent to lubricate the wider end of the rubber valve(as suggested by someone else in their description). I placed the valve into the washer in the same way the old one came out. I tightened the clamps and started the machine. No leak. I put the top and front on and have been happily washing since. This machine was given to us used by my mother-in-law. It is at least 25 years old.
I assumed we would have to replace the machine, but we repaired it for less than $20., including shipping. Thanks.

I went to the Internet and saw how to pry the front panel off the washer. This gave me access to the two belts and four pulleys underneath the washer; a pair for the Drive and a pair for the Pump. There was enough slack in the original belts that they came off with minimal effort. The new belts were easy enough to install. It took a mere seconds to install the new Spacers on the Front panel of the cabinet. The most time consuming portion of the project was getting the washer turned out of its tight corner to get access to the clips on the bottom of the front panel.

I tipped the washer up on 2by4 blocks used 1/4 inch rachet with 5/16 socket two remove 3 screws and the belt from underneath. Took clamps off hoses yahoo saved l00 bucks!

This job turned out to be alot easier than I thought thanks to the tips I received on the web site. First I removed the agitator with a small nut drive I believe it was 1/4". Than I removed the two screws holding on the lid and lofted it out of the way. This is where the Hammer drill comes in. I had read someone else had used WD40 to help break free the threads and get the retaining ring off the tub it self. I worked on this for about 20 minutes with lube and trying to tap it off with the hammer and tap method. Finally I looked over and sitting there on the self next to the washer was my hammer drill. It can't be any worse than banging on the thing with the hammer. (They proably don't reccomend) but with a straight tip and a couple of quick shots the gaint nut came right off. I will say that my washer being older I could barely even tell where the threads were so I figured why not. It worked great. I then took the tub ring(plastic) at the top off and removed tub. Again a couple of quick shots with the hammer drill and the ring came right off. I did spend a little time making sure everything was clean and then reassembled machine with no more leaks. It may sound strange but it worked great with no fighting the space constraints, the calcium buildup and no damage to machine. If it doesn't work get a bigger hammer. Good luck