MAV7504EWW Maytag Washer - Instructions

Removed the old hoses and screwed on the new hoses.

Watched video from on YouTube. Disasembled dryer by removing cap from timer knob. Pulling timer knob off the shaft. Removed three # 15 torx screws from the top of the dryer. Top panel rolled forward. Depressed plastic tab removed timer and unplugged wiring harness. Ordered parts from this site online. Parts arrived in 2 to 3 days. Parts were installed following reverse order from above.

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

Unplug electrical plug and shut off water supply. Putty knife to release latches at top left and right corners of flat top top where cloths go into washer. Take picture of wiring connections. Remove water diverter cover by unhooking snaps. Remove single screw holding water diverter. Remove single screw holding inlet valve and pull valve and water lines thru access hole. Disconnect wiring connectors and unscrew water supply lines. Reverse process to install.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.

The installation was extremely easy - videos sure helped. I would recommend this site for appliance parts - parts came ahead of schedule.

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

Remove back compartment, remove belt disconnect two water rubber tubes from the drain pump, unscrew three screws securing the drain pump from the frame. Replace with a new drain pump, secure to frame with thee screws, reconnect rubber tubes, and replace belt.

Pump is readily accessible at the back of the machine by taking off the access cover. First step is to disconnect power and remove drive belt off tub pulley which is the largest in the center - the takeup is in the drive motor mount but it seems easier to turn the larger pulley and wind the belt off. There are three 3/8 hex mount screws fastening the pump to the washer base and two hose spring clamps attaching the tub drain hose and outlet drain hose to the pump. Follow the directions in the utube video which is the best (most others don't give detailed directions and best method). The only caution I would give is that there is some water in the drain hoses so be prepared to mop it up with sponge and bucket or have some towels available. Install new pump (loose assemble two visible screws to locate pump and then loose assemble far side blind screw and tighten all 3),replace hoses snug to stops and assemble clamps, replace access panel and replace drive belt and plug washer back in.