BA1910 Maytag Washer - Instructions

disconnected power turned off water supply pulled washwer out from wall for easy access to area removed round inspection plate with screw driver removed four screw retaining syphon elbow inside machine pulled hose down removed broken piece install new syphon break elbow secured with 4 screws installed drain hose and new supplied hose clamp very easy great service great web site easy to locate part needed. my wife sells about 18 - 20 houses a year so im involved as her personel fix it man so the web site will be addedd to our list and refered to others

Read repair stories on website. Removed front & top to find leak, Ordered part. Replaced valve. Had trouble with clamp.It only caught in first slot, then broke. Had to go to hardware for one slightly larger.

pulled the washer drain hose off and replace it with a new one. it was so stiff it would not flex properly. Probably 30 years old. I broke the Syphon Break elbow because of the stiff drain hose. unscrewed 4 sheet metal screws where the Syphon Break Elbow goes through back of washing machine. opened the access hole for my arm below - 1 screw. reached up and pulled broken part out from the inside approx 12- 16 inches above. Slid the new part into place. remounted the 4 screws hold connection together. recovered access hole and attached new Drain hose with a band clamp. The new hose had 3 different size ends that can be cut to fit. I had to cut down to the smallest diameter hose. (1 inch, 1.25, or 1.5 inch). Ten to 15 minutes tops

Followed video that came with part.

I order a water inlet valve from this site It was the best buy around. The email from the site part came with a video how to change it. It was a 15 minute job. One 5/16 nut driver to remove the inlet valve and pliers to remove the hoes from the valve. Easy off easy on.

Terrified that the washer water value would blow due to the noise... Diagnosed the problem, ordered the part and it took only 10 minutes to fix. The hardest part was moving the washer in the confined space, which required moving the driver out and sliding the washer at a 45° angle in order to reach the access panel. Once access gained it was straight forward. Step 1 removed fill hoses from supply. Backed the valve assembly out; detached water hose from value assembly with nut driver; detached wires'; value released; added new value and reverse process. Checked for leaks, reassembled fill hoses with new washers (stainless steel hose), ran cycle, checked for leaks, replaced washer in original position Need commend the video producer and repair person in the video. The narrative gave me the confidence that, Yes, I can do this.

Unplug machine and remove drain hose clamp and hose from rear of the machine.Using Phillips head screw driver remove the 2 screws from the lower front panel of washer. Lift and remove front panel. Using a small socket, remove 2 screws from the inside top left and right of machine which secures the machines top cover and lift cover up (use duct tape to secure washer lid from opening). At the inside rear top of the machine is the Siphon Break Connector. Loosen clamps, remove old Siphon Break Connector and install new one. Reinstall top cover, front panel and then drain hose.

Watched your video and followed your instructions and it was very simple.We bought our maytag washer in 1988 next year it will be 30 years old we raised 3 children and for $21 and your video I hope to it last another 30 years

I watched your 'how to' video, then repeated the procedure on my own machine. The repair went pretty much like the video. The new valve corrected the problem, and in fact, fills the washer faster than the old valve. I also replaced the water supply hoses, as one started to leak after I jiggled it around during the repair. Very satisfied with the this sites experience.

removed cover, disconnected small water tube and disconnected electrical connections. Reversed above to install new piece. two nutdrivers required. Channel locks for supply hoses.

I removed the two hoses connected to the valve, then I removed the front panel by removing two screws on the bottom. I disconnected a drum hose connected to the top, tilted the top back, then separated the inlet valve from its metal housing by removing the screws holding it in place. I then removed the metal housing in order to have more access to the old valve. At this point, the valve was only held in place by a few wires. I noted which wires connected where and how the valve was oriented (Hot/Cold position), then removed the wire connections with pliers by grasping the connectors (not the wires). I then reversed this process to install the new valve.

We turned off the water, removed the hot and cold water hoses from the machine, then unscrewed the metal plate on the back of our washer that was covering the water inlet valve. Next we removed the output hose and pulled out the inlet valve. As we unhooked each electrical wire we immediatley hooked it to the same location on the new inlet valve. Then we rehooked the out put hose and reversed our steps to finish the job. Before putting the plate cover back over the inlet valve we filled the machine with cold water and ran it through all cycles to make sure we didn't have any leaks. The pictures/insturctions that came with the new part were helpful.

This was the first repair job that our 20 year old Maytag washer has needed, and it was nice to be able to do the job ourselves. Reading other customers's repair stories on your web site helped us diagnose our problem. I found it easy to locate and order the right part and it arrived two days after being ordered.

Performed repair through access cover in rear of machine. Removed screws with a nut driver and took out broken elbow. Pulled hose down to access hole to replace gasket then put back into position. installed elbow and reinstalled screws.
( this was tricky, have a helper to start the screws or place the screw in the nut driver with a piece of cloth to hold it in place), Make sure the screws are tightend evenly so the elbow sits completely against the gasket

The machine had leaked late last year; replacing the interior hoses fixed it, but the leak came back.

To diagnose the problem, I used a short, #2 phillips screwdriver to remove the two retaining screws under the front panel indentation. I pivoted the front panel toward me, unhooked it from its retaining hangers, and set it aside.

Inspection revealed that water was running down the exhaust hose from the siphon break, so I unplugged the machine, pulled it away from the wall, removed the two top retaining screws and pulled the top toward me. There was enough play in the wiring harness to leave everything connected.

I used a socket wrench to loosen the hose clamp at the bottom of the siphon break, and to remove the 4 hex head screws that hold the siphon break to the back of the machine. A few twists freed the siphon break, and one glance revealed that its top was covered with soap scum. It clearly needed replacement, so I ordered the part.

Replacement was a piece of cake. I mounted the gasket in the new siphon break, moistened its tube, twisted it into the hose, and tightened the clamp with a socket wrench. I then mated the new part with the old exit elbow, lined up the holes, and installed the retaining screws. I pushed the top back into position, installed the top retaining screws with a socket mounted on a universal nut driver handle, rehung the front panel, and installed the two retaining screws. Presto, good as new!

Everything else is clean. I would much rather replace a few parts and continue using "Old Reliable" than pony up $800 on a new machine.

I removed the two screws holding the front panel and lifted out of the way. I then removed the front two bolts holding the top to the frame. I slid the top forward providing access to the interior. I then removed the four screws holding the discharge unit against the back panel. I removed the broken elbow and installed the new one. I reversed the removal procedure and installed the discharge hose to the new elbow. (Note: the new elbow was slightly smaller at the discharge end than the old one. The discharge hose had a larger inside diameter than the elbow. Probably due to the age of the machine). I will pay attention to the discharge hose if I have to move the washer again.