MVWP575GW0 Maytag Washer - Instructions

1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!

This also gave me a chance to clean the agitator thoroughly!

first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.

That OK , easy.

First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.

As far as repairs go, this one is really easy.

Followed instructions on website video.

Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet extension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.

Removed the agitator cap, then removed the plastic, spring loaded retaining part (needed a square head tool). Once out, the cog retainer came out, replaced all four cogs, and replaced in reverse. Easy as pie & took 10 minutes!!

Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.

Sincerely,

Ken Lancaster

Pulled up and removed the fabric softner dispenser. Then I pulled up and removed the cap barrier to have access to the screw. Removed the screw and pulled up the cloths mover. Tunrned the cloths mover over to remove the bearing cam to remove the broken agitator cogs and replaced them with the new ones. I held the bearing cam with my right hand and held the cloths mover with my left hand turning it slowly with my left hand and lightly pushing down with my right hand until the cloths mover made contact with the grooves of the shaft and it sunk down on the shaft. Replaced the screw and washer then the cap barrier , next the fabric softner dispenser. Took 10 min. to complete the job. Now my washer runs like new ! Plus, I have a happy wife!

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.

To replace the dogs that cause the ratcheting motion:

I removed the softener cup by pulling straight up. (You've probably found, as I have, that the softener cup and the bleach dispensers are problematic: the softener cup must be cleaned with every use or the old softener liquid turns to glue, and the bleach dispenser mechanism plugs and distributes bleach onto your next load, ruining entire loads of clothes.)

Then I lifted the cap covering the retaining bolt by inserting a screwdriver alongside in the square holes provided, loosening it, and lifting it out.

Then I used a socket and a very long extension to remove the retaining bolt. I lifted the agitator straight up.

The next step can be a problem: I survived it (though I did strain my back). What's required, as you can see by reading the preceding letters, is to lift sharply on the upper agitator while holding the lower agitator with your bare feet or some soft shoes. What this does, at least on my model, is to break off the tabs that are fused together over the ratcheting-dogs, which are the focus of the repair. (These tabs hold the upper and lower assemblies together, moving the dogs assembly with the lower agitator.) In my case, one of the tabs broke off a half inch below the top, but that wasn't catastrophic and I didn't lose the rest of them, so when I reassembled the two halves still snapped back together.

One problem was that when I jerked the two assemblies apart, the parts of the dogs assembly went flying. Everyone had said to make sure everything went back the same way it came apart--for me there was no way to tell what that way was, but common sense tells you which way to reinstall the new dogs; they have to catch every stroke.

To reassemble, position the dogs with the retainer cup inverted. Then hold them upside down while sliding the upper agitator down over them. This holds them in place. When sliding the upper agitator down onto the lower, make sure the slots line up and use a smooth even pressure. Snap the two halves together, bolt the agitator back into the machine, replace the cap with the large o-ring (make sure you clean and/or replace the o-ing), and reinstall the softener cup.

Et, voila! You're back in business.

First I popped off the very top cap of the agitator. I then used a socket extension to access the mounting bolt in the interior of the agitator. Once the bolt was loose i pulled the agitator off and dropped out the middle piece. With this out i switched the 4 cogs with the old. I then held the agitator assembly upside down and placed the middle piece back in. The most difficult part was aligning the agitator back onto the bottom part. Screw it back in place and pop the top back on.

The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great

I popped the liquid detergent cap off of the top of the Agitator. I then removed the seal cap to expose the Agitator dog assembly and bolt. I removed the entire Agitator dog assembly and Agitator by removing the single 7/16? bolt. I pulled the old dogs out, put the new dogs in and reassembled the Agitator Assembly.

Works like new!!