MAH20PDAWQ Maytag Washer - Instructions

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!

First and foremost, disconnect the power before anything else, then remove the door, access panel, and front of the washer,I then detached the front of the rubber boot so I could remove the plastic panel that it attaches to, that exposes the springs, I then used a vice grip to remove the springs replacing them one at a time, I also replaced the struts in the rear of the machine which requires removing the rear panel, and I used a bottle jack to support the rear of the washer tub while I changed the struts, I changed the struts first which only helped a little, the springs made the job complete and the washer now completely wrings the clothes to a damp state that dries quickly.

I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all

The whole thing is on YouTube beating out bearings was the only difficult part

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

remove door phillips remove front push down and pry out remove soap tray phillips remove two nut screws to lift up topy open tie or support top up remove bad contactor phillips normaly open check with continunity tester replace and reverse procedure

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

diagnosed problem (hole in drainage pump). unplugged, took service panel off rear, removed hoses, twisted pump counter clockwise. dropped new pump in, made connections, and it was good as new.

The front seal had a long slit which leaks water during washing cycle. We followed the repair video every steps and got the old seal off really easy, the most difficult step is to tie the cable with the spring, it is too strong and can not be done with one person. All steps are the same as shown in the video. Thank you for providing the video and the part.

I followed the video for the installation. I did find that installing the spring was no way as easy as it looked in the video. Otherwise, OK.

Following the information on the web it simplified this repair a great deal. Disassembled the front of the machine, then pulled it out from the wall, removed the rear panel. Removed the belt & pulley and knocked the shaft loose from bearings. Removed the tub and using the brass bar drove the rear bearing out first then removed the seal and front bearing. The seal has to come out first so the plastic spacer can be removed, used the brass bar from the rear of machine to drive front bearing out. Cleaned up all parts and reassemblied. Replaced the motor isolators and drive belt with new since I was in the machine that far. Removed the soap & bleach tray and cleaned up all those parts. re-assembled and washed a load of rags to test machine. Sounded like a new machine. Sourced the new bearings from a bearing supplier they are 6200 Series bearings, Rear 6206-2RS; Front - 6207-2RS. Had I not made this repair I would have been buying a new washer & dryer so this job for a little over a hundred bucks saved me thousands! Thanks to PARTSELECT for all this information!!

Unscrewed old screws, removed old plastic pieces, and replaced