LAT5006AGE Maytag Washer - Instructions

Disconnected power. Then I removed the cover to the console on the back to gain access to the lid switch. Removed the switch assembly by hand and disconnected from electrical plug on machine. Attached new assembly unit to plug and reinserted new assembly onto machine. Reattached cover to console.

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Make sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.

Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!

Removed the damaged legs, replaced with parts from this site and leveled the washer .

The hardest part was actually finding the right part. It was easy to take of the control panel. make sure you unplug and plug in the correct wires....

I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.

That's about it.

I turned the dial to other selections and nothing worked, no power. I checked the fuse box, but nothing was off, and then I checked to make sure electricity was working with a light bulb. I googled the situation and came across this site and read other posts as they sounded exactly like what I was experiencing. I ordered the complete lid assembly not just the fuse. The item arrived quickly in two days. After about an hour, as it was pretty easy to replace, the washer was working again! Thank you all for posting, as it saved me at least a couple hundred dollars.

Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

I removed the lid switch assembly and replaced it with the new lid switch assembly. The assembly included the lid switch, lid. check switch, and fuse. It came as one complete part.

I looked at the machine diagram on the website and removed the screw on the bottom and lifted up the from panel which allowed me to have easier access to the fill injector. Then I removed the back panel off of the control panel on the top of the machine and removed the screw that held the fill injector in place, attached the new fill injector using the hose clamp I ordered with the part ( you need a new hose clamp because the other one is useless after you remove the old injector). Tightend up the screw to hold the injector in place and replaced the back panel and front panel. It was an easy repair and only cost $28.00 with shipping. I easily saved $150.

I followed the instructions on this website to a T. You can take the front cover off and you will notice a small drip from the tub area where the Hub bearings (above the tranny) meets the washing tub. Once you've identified that the leak is indeed coming from that area and not a loose tube. Allow the washer to complete the job and drain the water. Then simply unplug washing machine before starting the process of the repair. It is very important to remember that you must have a spanner wrench before attempting to perform this repair. keywords=spanner+wrench came within two days with Prime Shipping. Also be sure to order the replacement parts from this site. It takes about 3 days to arrive however so be prepared to be without a washer for a few days. Other than that just follow the instructions provided and there is a very good step-by-step video on this site .

I followed the direction came with the part.

• I unplugged power electric wire from the wall.
• Unscrewed total of five screws from the back of the top console.
• Removed the top console to gain access the switch.
• I took pictures of the switch position for a future reference.
• Unplugged the switch wire by just pulling the plug.
• Carefully removed the switch and pulled the plunger out plunger assembly.
• Entered a new plunger in first and inserted a new switched carefully.
• Opened and close the lid few times to check the switch is going on an off properly. You will hear clicking sounds.
• Plugged the switch wire to the new switch.
• Reinstalled the console and screwed back the five screws.
• Plugged back the electric plug in wall outlet.
• Tested the washer by washing a full load of clothes.

The whole process took me about 30 minutes.

-Abhay