MAV6548AWQ Maytag Washer - Instructions

The installation was extremely easy - videos sure helped. I would recommend this site for appliance parts - parts came ahead of schedule.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.

I couldn't figure out how to open the machine to take out the old unit. I finally resorted to the internet, and found a good UTube video which showed how to use a putty knife to release a couple springs that allowed the top of the washer to raise up. The rest was easy. If you're a do-it-yourselfer, and get stuck, consider a UTube search. You might uncover a pearl that helps.

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

used video provided on repair procedure.

Turned off the water supply. Removed clothing and bailed out water fro tub. Removed back access panel. Turned washer over to access the bottom and removed drive belt by turning the large pulley attached the drum while pulling the belt over the pulley. Next remove the two hoses attached to the pump, remove the screws holding the pump on and remove the pump. Replace the pump by reversing the procedure, as for replacing the drive belt, place the belt on the motor and pump first and start it on the larger pulley and hold it on while you turn the pulley, it will pull the motor adjustment as you turn and when fully in the pulley it will be properly adjusted. Then replace the access panel, turn the washer upright, push back in place, turn on the water supply and replace the drain hose. Back in business. For me, while I was waiting for the new pump to arrive, I took the time to remove the agitator and tub and give it a good cleaning inside and out, but that's me.

A few youtube videos to replace the motor and belt. From there on out it was pretty easy. Separate the top from the spring clips. Remove front panel. Remove motor once inside and remove belt from underneath. After motor was out, Remove base from old motor and attach to new. Reassemble and voila. Good as new.

Unlike most videos, mine had a solid frame, no access panels. Following, is my disassembly & repair: I disconnected the water supply lines and drain hose. I slid the washer out into the center of the garage & removed the 9 base screws from the base plate. I slid the frame away from the base, leaving the working parts exposed. After pulling the working mechanisms from the outer frame, I turned it (drum, transmission & base) upside down. I used a pair of vise grips, pinched them onto each spring & removed them, using a downward motion it was a lot easier. I placed the base plate aside, removed 3 opposing screws holding the snubber ring & put 3 longer 8-32 screws in to hold the brake assembly. Then I removed the 3 remaining screws, lifted the plate & replaced the ring. Then I reversed the process, replacing the old springs with new ones & finished the job in about 2 hours.

As a 78 year old senior, I no longer have the upper strength and agility to remove the springs. Had to remove the washer casing (9 screws and 3 bolts), which gave me full access to r disconnect the springs, remove the tub, replace the snubber ring and reinstall the springs. The complete repair took me 6 hours, no assistance and was very thankful for the excellent videos available online.
Parts arrived in 3 days, fantastic delivery service, great prices and fixed my washer for $107.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

This was a very easy fix.....roll belt off....roll new belt on....seemed to help not sure if it fixed problem....might try pulley and bearing kit next

Pump is readily accessible at the back of the machine by taking off the access cover. First step is to disconnect power and remove drive belt off tub pulley which is the largest in the center - the takeup is in the drive motor mount but it seems easier to turn the larger pulley and wind the belt off. There are three 3/8 hex mount screws fastening the pump to the washer base and two hose spring clamps attaching the tub drain hose and outlet drain hose to the pump. Follow the directions in the utube video which is the best (most others don't give detailed directions and best method). The only caution I would give is that there is some water in the drain hoses so be prepared to mop it up with sponge and bucket or have some towels available. Install new pump (loose assemble two visible screws to locate pump and then loose assemble far side blind screw and tighten all 3),replace hoses snug to stops and assemble clamps, replace access panel and replace drive belt and plug washer back in.

Remove back compartment, remove belt disconnect two water rubber tubes from the drain pump, unscrew three screws securing the drain pump from the frame. Replace with a new drain pump, secure to frame with thee screws, reconnect rubber tubes, and replace belt.