MAH14PDBGW Maytag Washer - Instructions

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

Replaced wax motor. You must also replace R11 (3.9 Ohm carbon film resistor (1/4 watt), Q6 Triac (Mouser 526-NTE5656), replaced Jp 18 (jumper) with a fuse (Mouser 576-0251.500HAT1l. This job requires the use of a solder sucker in order to remove parts without lifting up cooper traces.I have had experience with many electronic projects,and could have done this one easier if I still had the proper tools.A solder sucker is cheap, and without it, you will damage the traces. I did, but used a continuity checker to verify I made solder contact with the traces. I have six of these stacked washer/dryers. All failed after about a year of use. I am in absolute disbelief regarding all the stories about how easy this repair is.

The video was great. The only problem was getting the spring back on. It was way too stiff, so I put it in a vise and stretched it a bit. It's a bit fussy but your site made it go pretty easy. thanks

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

Followed the video, besides the spring, everything was easy.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

I followed the video which I might say is somewhat misleading for the Maytag Neptune washing machine. This is the one with a recall due to mildew and mold build up on the Door Seal (Bellow). First to take it apart you really need a 8mm socket in order to get into tight spaces. Once you start using the socket everything will come apart quickly the last being removing the old Bellow. I found this is easy if you just roll the spring toward the front using a screw driver. Once it clears the front of the Bellow, the cable will fall off along with the spring. You can now remove the old Bellow. The next step is to insert the new Bellows on the rim of the tube. I started by attaching the drain hose at the bottom and then from the video, started at the top make sure you have it center correctly and worked down one side pushing the Bellows on the rim and then do the same thing to the other side part way. Alternating from one side to the other until you reach the bottom. The Bellow is now on the tube, NOW the hard part. First, the old spring was stretched. I bought a new spring at Home Depot. I next took the cable and placed it around the tube with the ends at the top. Make sure to thread the cable carefully so it is in place. Watch out for plugs and the drain at the bottom of the tube. I attempted to attach the spring by myself using a long nose plier and a Grip plier but just could not stretch is far enough by myself as shown in the video. I next took a 16 ga insulated wire you could also get at Home Depot and attached it to each end of the cable and twisted it together in the middle with pliers so it was tight and cut off the excess wire. I attached one end of the spring through the right eyelet on the cable and using the grip pliers and BOTH hands on the grip pliers pull the spring and threaded it through the left eyelet. Hold the spring in place I now pushed the stretched spring against the back lip of the tube. I removed the 16 ga wire buy cutting off the ends and carefully pulling it away. Next, I just followed the video. I pushed all the tabs on the Bellow in to the holes on the tub and then screwed the parts back in reverse order. Good Luck Al

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!

Removed front panel and door, lifted top cover to access door lock. To remove the wax motor, you need to remove the Door Lock/Spin enable switch. Important note, there are two switches so to completely rebuild the door lock, you need get two of the Door Lock/Spin Enable switches. Same part/part number, one is for the door lock and the other for the Spin enable.

The front seal had a long slit which leaks water during washing cycle. We followed the repair video every steps and got the old seal off really easy, the most difficult step is to tie the cable with the spring, it is too strong and can not be done with one person. All steps are the same as shown in the video. Thank you for providing the video and the part.

Followed instructions that came with replacement part, good as new!

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!